Tecfrigo SNELLÈ 750 GBT-R-VU Zusammenbau Und Betrieb Seite 7

5. CLEANING OF THE INTERNAL GLASS PANELS
1. Only clean the internal component and glass panels with a soft,wet sponge and a neutral detergent.
2
. Dry with care using a soft cloth
External cleaning
1 .For the glass panels use the same products as used for the internal cleaning.
protection tape from the steel panel and from the grids.
6. CONNECTION TO MAINS
1 . Ensure that mains voltage and frequency are the same as those stated on the rating plate ( ) attached
2.
to the appliance. Ensure that the supply socket has the following characteristics:
earthed. It is appropriate for the nominal current as set out on the rating plate. It complies with the IEC b)
-
regulations: Magneto-thermic differential switch with In = nominal value as stated on the rating plate;
-
Differential with Id sensitivity = 30 mA.
4 . The connecting cable to the appliance is H05 VVF, designed for internal use only.
appliance, during the trasport or storage, has been erroneously placed in horizontal position or upside-
down, it must be left in the correct position for at least 3 hours before connecting it to the electrical supply.
5
. Insert the plug (do not use triple and reduction outlets) (see picture 5).
7. CONTROLS
The controls of the appliance are situated at the front inside a protected recess.
for turning on the refrigeration system.
3. Rotation switch: it sets the rotary shelves into motion.
the appliance. Thermostat
display the temperature set-point,which can be changed by pressing key
8. CHECKING THE CORRECT FUNCTIONING
MAKE SURE THAT: 1 . T he plug is connected
thermometer shows the desired temperature for the foodstuffs to be stored in. . Internal light and
rotation switches are on. . The door is closed. . The appliance is not exposed to the direct light of the 5
sun or to high powered lamps. . The room temperature does not exceed that in which the appliance is
designed to work normally, i.e. +30° C 55% r.h. (Climatic class 4). . The compressor ventilation grilles
are free from obstruction for at least 30 cm.
(Max 6 kgs for each shelf), in order to ensure a good circulation of the cool air, especially between the
rear glass panel and the shelves, where the air outlets are.
9. REPLACEMENT OF INTERNALIGHT
1 . Switch off electricity supply. . Unscrew the screws fixing the upper light holder. . Detach the
fluorescent tube from the upper lamp holder. . Remove the tube from the lower lamp holder. . Remove
the transparent protective tube
reverse order (see picture 7).
10. REPLACEMENT OF THE DOOR MAGNETIC GASKET
1 .Open the door. 2. Take hold of the magnetic gasket with your hands and remove it from the frame.
3 . Insert the new gasket and press all around it when in place
11. INTERNAL CLEANING (EVERY 15 DAYS)
GBT / GBT VU 1 . Switch off the appliance.
3. Remove the goods and put them in a suitably refrigerated place. . Remove the bottom cap, that you
will inside of the appliance.
pipe, which can be accessed by removing the left hand grill. Allow the pipe to drip in a suitable external
container. . Do not use sharp or pointed metal objects to remove ice from the evaporator. . Dry all parts 6
with care. . Leave the appliance to dry with the door open before restarting. 8
appliance. 2. Open the door and remove the refrigerated goods.
appliance with a sponge dipped in water with a little sodium bicarbonate. Dry with care (see fig. 9).
Operator's guide
3 . Ensure that there is no danger of explosion (AD) in the room.
2. Light switch
for adjusting temperature in the appliance.
. 2 . Refrigeration unit switch is on (green light lit up). . The
6
7
9. The foodstuffs are placed on the shelves in the right way
2
4
(NO LED) 6 . . Replace the fluorescent tube. . Replace everything in
2. Open the door and remove the refrigerated goods.
5. Remove excess water from the drainage outlet by means of the drainage
7
2
c)
1. Refrigeration switch
for turning on the light inside the appliance.
6. Thermometer for reading the temperature in
a) Press key
5 "UP"
or
4
8
7
(see picture 8).
4
R and G1 1.
3. Wipe the internal surfaces of the
. Remove the
A
a) It is properly
Notice: in case the
4 "SET or P" once to
7 "DOWN"
(see fig. 6)
3
3
5
7
Switch off the
I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO