Residual Risks; Technical Data; Operation - Scheppach PM600 Originalbetriebsanleitung

c) Avoid having any part of your body in the re-
gion in which the power tool is likely to move
in event of a kickback. The kickback will force the
power tool in the opposite direction to the direction
of rotation of the grinding disc at the blockage.
d) Take special care when working near corners,
sharp edges, etc. Avoid allowing the accessory
tool to bounce back from the workpiece or jam.
The rotating accessory tool is more likely to jam in
corners or sharp edges or if it rebounds off them.
This can cause a loss of control or kickback.
e) Do not use chains or toothed saw blades. Such
accessories often cause a kickback or loss of con-
trol over the power tool.
Safety Warnings Specific for Polishing Operations:
• Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely.
Tuck away or trim any loose attachment strings.
Loose and spinning attachment strings can entan-
gle your fingers or snag on the workpiece.

Residual risks

Even if you use this electric power tool in ac-
cordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
• Damage to hearing if no suitable ear protection
is used.
• Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.

Technical Data

Voltage
Power rating
Speed n
Polishing / sanding disk
diameter
Connection thread
Protection class
Weight
Noise and vibration values
The total noise values determined in accordance
with EN 60745.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 60745.
14 І GB
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
230 V~ / 50 Hz
600 W
1200 - 5000 min
-1
Ø 125 mm
M14
II
2,1 kg
80 d(A)
3 dB
91 dB(A)
3 dB
Vibration emission value ah = 6,09 m/s
K uncertainty = 1,5 m/s
2
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Before starting the equipment
Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Warning! Always pull the power plug before mak-
ing adjustments to the equipment.
Fitting the additional handle (fig. 2)
• The polishing machine must not be operated with-
out additional handle (3).
• The additional handle can be secured in any of 2
positions (A, B).
Tool side
Left (position A / as shown)
Right (position B)
Attaching/Removing the rubber disc (fig. 1)
Warning! Turn the machine off. Pull out the power
plug!
Press the spindle lock button (1).
1.
Use your hand to screw the rubber disc (6) from or
2.
onto the spindle.
Notice!
Only ever press the spindle lock when the motor
and grinding spindle are at a standstill! You must
keep the spindle lock pressed while you change
the wheel!
Attaching/Removing the polishing bonnet (fig. 1)
Warning! Turn the machine off. Pull out the power
plug!
The polishing bonnet (5) can be attached to the
1.
rubber disc (6) via a hook and loop fastener.
To remove it, simply pull the polishing bonnet (5)
2.
from the rubber disc (6).

Operation

Switching on/off (fig. 1)
To turn the machine on, press the ON/OFF switch (4).
To turn the machine off, simply release the ON/OFF
switch.
2
Suitable for
Right-handed users
Left-handed users