Specifications - Makita DCO140 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Red indicator
1-2. Button
1-3. Battery cartridge
2-1. Star marking
3-1. Thumb screw
3-2. Shoe
4-1. Slide switch
5-1. Collet nut
5-2. Shoe
5-3. Shaft lock
5-4. Tighten
5-5. Loosen
6-1. Collet cone
6-2. Bit
6-3. Collet nut

SPECIFICATIONS

Collet chuck capacity
Rated speed (n) / No load speed (n
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting gypsum, wood, plastic
and soft wall tiles.
Noise
The typical A-weighted
according to EN60745:
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
Vibration
The vibration total
determined according to EN60745:
Work mode : rotation without load
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
Explanation of general view
11-1. Thumb screw
11-2. Shoe
12-1. Projections
12-2. Shoe
13-1. Thumb screw
13-2. Circular guide
13-3. Shoe
13-4. Loosen
13-5. Tighten
14-1. Knob
14-2. Tighten
14-3. Loosen
15-1. Knob
16-1. Thumb screw
16-2. Vacuum cover
Model
)
0
Overall length
Net weight
Rated voltage
noise level determined
) : 77 dB (A)
pA
value (tri-axial vector
2
) : 2.5 m/s or less
h
2
DCO140
3 mm, 6 mm or 1/8", 1/4"
30,000 min
313 mm
1.6 kg
D.C. 14.4 V
ENE012-1
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
ENG905-1
The vibration emission during actual use of the power
•
tool can differ from the declared emission value
depending on the ways in which the tool is used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENG900-1
For European countries only
sum)
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Cordless Cut-Out Tool
Model No./ Type: DCO140, DCO180
ENG901-1
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
Standard or standardized documents:
EN60745
4
17-1. Tool
17-2. Vacuum cover
17-3. Hose 28
17-4. Hose for vacuum cleaner
17-5. Vacuum cleaner
18-1. Tool
18-2. Vacuum cover
18-3. Hose 28
18-4. Dust collector
19-1. Limit mark
20-1. Holder cap cover
20-2. Screwdriver
21-1. Brush holder cap
21-2. Screwdriver
DCO180
3 mm, 6 mm or 1/8", 1/4"
-1
30,000 min
313 mm
1.7 kg
D.C. 18 V
-1
ENH101-17