Interlogix DD490 Serie Installationsanleitung Seite 4

Notes
•
Enabling the walk test will not clear alarm memory. After
disarming the system after an alarm, you may switch to
walk test. When you switch back out of walk test, the
indication of memorized alarms will reappear. Only when
CV is re-applied to terminal 9 (i.e. system is rearmed) will
LEDs and memory be cleared.
•
To enable the walk test LED without a remote CV input,
connect a link between terminal 2 and 10, J2 = "+".
•
Microwave disable. The DD497/DD498 have the additional
feature that whenever the system is disarmed with the
walk test off, the microwave transmitter will be switched
off. The detector will then operate as a PIR only. In all
other configurations the unit operates in dual technology
mode.
Selecting the coverage patterns
See Fig. 5 and 6.
Mask the appropriate mirror curtains with the adhesive labels
provided and reassemble the sensor module.
For example: See Fig. 5 for mirror curtain coverage pattern
corresponding to curtain 3A and 3B, 6A and 7B masked.
Caution: Removing label(s) can damage the mirror surface!
The coverage pattern can be changed to fit specific
requirements using the mirror masks as shown (Fig. 6). Mask
off unused curtains which might otherwise be looking at walls
or windows very close to the detector.
Window mask
See Fig. 7.
When there are objects close to (within 1.5 m) or directly under
the detector, fit the mask to the inside of the window. This
disables the part of the curtains looking at the object, whose
closeness might otherwise destabilise the detector.
Specifications
Limited input power source
Peak-to-peak ripple
Current consumption:
DD495/DD497
Normal operation
Max.
DD496/DD498
Normal operation
Max.
Mounting height
Target speed range
Microwave frequency:
DD495C/UK, DD496C/UK,
DD497C/UK, DD498C/UK
DD495, DD496, DD497, DD498
Alarm output
Alarm time
Tamper output
4 / 16
9 to 15 V (12 V nom.),
8 A max. fuse
2 V (at 12 V)
Form A
14.5 mA
16.5 mA
Form C
19.5 mA
26.0 mA
1.8 to 3.0 m
0.2 to 3.0 m/s
2450 MHz
2406 MHz
80 mA at 28 V max.
min 2.5 s
100 mA at 28 V max.
Walk test
Max. microwave output power at 50 cm
Continuous emission
Operating temperature
Relative humidity
Size
Weight
Mirror type
Number of zones
Viewing angle (wide-angle)
Detection range
IP/IK rating (with sealed cable entry)
Usage restrictions
Certification and compliance
Manufacturer UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings THESE PRODUCTS ARE INTENDED FOR SALE
and disclaimers TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY "AUTHORIZED
DEALER" OR "AUTHORIZED RESELLER", IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/
Certification
European Union UTC Fire & Security hereby declares that this
device is in compliance with the applicable
directives
requirements and provisions of all applicable rules
and regulations, including but not limited to the
Directive 2014/53/EU. For more information see:
www.utcfssecurityproducts.eu
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.utcfssecurityproducts.eu/recycle/
Contact information
www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.interlogix.com/customer-
support.
P/N 143690999-4 • REV F • ISS 28FEB19
0 V to terminal 8
Switch on: 0.005 µW/cm²
Switch off: 0 µW/cm²
−10 to +55°C
30 to 95%
125.5 x 74 x 53.5 mm
150 g
7C60D75
7
60°
20 m
IP30 IK02
DD495, DD496,DD497,
DD498 are not allowed to be
used in the UK
or scan the QR code.