Makita DCS553 Betriebsanleitung Seite 10

Dust box
CAUTION:
Do not touch saw dust and the
dust box with bare hands immediately after the
operation. They may be extremely hot and could
burn your skin.
CAUTION:
Do not cut the material on which
thinner, gasoline, grease, or other chemicals are
applied. T h e sa w d ust o f su c h materials c an d amage
t h e d ust bo x an d result in breakage w h i c h c an c ause
personal injury.
CAUTION:
W ear eye protection or goggle
when emptying the dust box.
Saw dust is collected into the dust box. Periodically
d ump t h e sa w d ust in t h e d ust bo x be f ore it gets f ull.
P us h t h e le v er on t h e d ust bo x to open t h e li d . D ump
t h e sa w d ust w h ile t h e rear o f t h e tool f a c es d o w n w ar d .
Fig. 9 : 1. L i d 2. L e v er
Fig.10
Hook
Optional accessory
CAUTION:
Always remove the battery when
hanging the tool with the hook.
CAUTION:
Never hook the tool at high loca-
tions or on the surfaces where the tool may lose
the balance and fall.
CAUTION:
Do not pull the tool downward
when it is hooked.
CAUTION:
Always fold the hook when operat-
ing the tool.
The hook is convenient for hanging the tool temporarily.
Fig.11
A tta c h t h e h ook w it h t h e s c re w s as illustrate d .
Fig.12: 1. H ook 2. S c re w
To use the hook, simply turn the hook until it snaps into
t h e open position.
When not in use, always turn the hook until it snaps into
t h e c lose d position.
Fig.13: 1. O pen position 2. C lose d position
Electric brake
T h is tool is e q uippe d w it h an ele c tri c bla d e brake. I f t h e
tool consistently fails to quickly stop the circular saw
bla d e a f ter s w it c h le v er release, h a v e tool ser v i c e d at a
Makita ser v i c e c enter.
CAUTION:
The blade brake system is not a
substitute for blade guard. NEVER USE TOOL
W ITHOUT A FUNCTIONING BLADE GUARD.
SERIOUS PERSONAL INJURY CAN RESULT.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Hex wrench storage
W h en not in use, store t h e h e x w ren c h as s h o w n in t h e
figure to keep it from being lost.
Fig.14: 1. H e x w ren c h
Installing or removing the circular
saw blade
CAUTION:
Use only the Makita wrench to
install or remove the circular saw blade.
CAUTION:
W hen installing the circular saw
blade, be sure to tighten the bolt securely.
CAUTION:
Be sure the circular saw blade is
installed with teeth pointing up at the front of the
tool.
Fig.15: 1. S h a f t lo c k 2. H e x w ren c h 3. T ig h ten
4. L oosen
T o remo v e t h e c ir c ular sa w bla d e, press t h e s h a f t lo c k
fully so that the circular saw blade cannot revolve and
use t h e h e x w ren c h to loosen t h e h e x bolt. T h en remo v e
the hex bolt, outer flange and circular saw blade.
Fig.16: 1. H e x bolt 2. Outer flange 3. C ir c ular sa w
bla d e 4. Inner flange 5. C up w as h er
T o install t h e c ir c ular sa w bla d e, f ollo w t h e remo v al
pro c e d ure in re v erse.
WARNING:
BOLT SECURELY. Also be careful not to tighten
the bolt forcibly. Slipping your hand from the hex
wrench can cause a personal injury.
WARNING:
be sure to install it on the spindle. W hen install-
ing, choose a correct side on which protrusion
fits into the circular saw blade hole perfectly.
Mounting t h e c ir c ular sa w bla d e on t h e w rong si d e
c an result in t h e d angerous v ibration.
Blade guard cleaning
W h en c h anging t h e c ir c ular sa w bla d e, make sure to
also c lean t h e upper an d lo w er guar d s o f a c c umulate d
metal c h ips as d is c usse d in t h e Maintenan c e se c tion.
S u c h e f f orts d o not repla c e t h e nee d to c h e c k lo w er
guar d operation be f ore ea c h use.
10 ENGLISH
BE SURE TO TIGHTEN THE HE X
If the inner ange is removed,