Stiga Cruiser 430 Li 80-Serie Gebrauchsanweisung Seite 153

15. The display shows
ER3 (Fig.35.B) (type
"II" handle - Advan-
ced Series).
16. The display alterna-
tively shows: ER1
+ OPC (Fig.35.B)
(type "II" handle -
Advanced Series).
17. The display shows
ER1 (Fig.35.B) (type
"II" handle - Advan-
ced Series).
18. The display alterna-
tively shows: 100%
+ ER3 (Fig.35.B)
(type "II" handle -
Advanced Series).
19. The display shows
ER2 (Fig.35.B) (type
"II" handle - Advan-
ced Series).
20. The display alternati-
vely shows ER2+ER3
(Fig.35.B) (type "II"
handle - Advan-
ced Series).
21. The cut grass is
not collected in the
grass catcher.
22. The cut grass is
not collected in the
grass catcher.
23. Mowing is difficult.
24. Excessive noise and/
or vibration is experien-
ced whilst working.
25. Battery power re-
serve is low.
26. Battery power re-
serve is low.
27. The battery charger is not
recharging the battery.
The thermal protection has tripped
due to overheating of the motor.
Thermal protection has tripped due to
excessive current absorption caused by:
• Excessively high grass cutting.
• Obstructions that prevent
rotation of the cutting means.
• Too much grass debris accumulated
in the chassis and discharge channel.
Drive motor over current for heavy
working conditions (drive under stress).
Anomaly in the electrical
connection of battery and motor.
Cutting means blocked.
Motor anomaly.
The cutting means has collided with a
foreign object and received a knock.
The inside of the chassis is dirty.
The cutting means is not
in good condition
Cutting means fittings are loose or
the cutting means is damaged.
Severe working conditions requiring
greater current absorption.
Battery is insufficient for
operating requirements.
Battery is not correctly inserted
in the battery charger.
Wait for at least 5 minutes and
then restart the machine.
• Set a higher cutting height when the
grass is very tall, then set a lower height
and cut the lawn again (par. 6.4.1).
• Remove the obstructions (par. 7.3.2).
• Clean the machine (par. 7.3.1)
Wait for at least 5 minutes and
then restart the machine.
– Make sure that the wheels are not
blocked. Clean as needed.
– Check the slope of the land you
are working on (par. 6.4.1).
Remove the safety key and contact
the Technical Assistance Centre for
checks, replacements or repairs.
Turn the machine off, remove the
safety key and wear work gloves.
Check and eventually remove any obstructions
in the machine lower side (par. 7.3.2) that
prevent rotation of the cutting means.
If the problem continues, contact an
authorised Technical Assistance Centre for
checks, replacements or repairs (par. 8.1).
Remove the safety key and contact
the Technical Assistance Centre for
checks, replacements or repairs.
Immediately turn off the motor
and remove the safety key.
Inspect for damage and contact a Technical
service centre for the replacement of the
cutting means if necessary (par. 8.1).
Clean the inside of the chassis to
ease the grass discharge towards
the grass catcher (par. 7.3.2).
Contact a Technical service centre
for the sharpening or replacement
of the cutting means.
Immediately turn off the motor
and remove the safety key.
Contact an authorised Technical
Assistance Centre for checks,
replacements or repairs (par. 8.1).
Optimise operations (par. 7.2.1).
Use a second battery or extended
battery (par. 15.2).
Check it is correctly inserted (par. 7.2.3).
EN - 15