Torque Adjustment - Ingersoll-Rand LD12 Serie Technische Produktdaten

EN
Model(s)
LD2206RP5-Q4-DI Pistol, Trigger Start Shut-off 2.3 - 9.3 (1.7 - 6.9)
LD2210RP1-Q4 Pistol, Trigger Permit Shut-off 2.1 - 5.7 (1.5 - 4.2)
LD2210RP5-Q4 Pistol, Trigger Start Shut-off 2.1 - 5.7 (1.5 - 4.2)
LD2210RP5-Q4-DI Pistol, Trigger Start Shut-off 2.1 - 5.7 (1.5 - 4.2)
LD2216RP1-Q4 Pistol, Trigger Permit Shut-off 1.8 - 3.8 (1.3 - 2.8)
LD2216RP5-Q4 Pistol, Trigger Start Shut-off 1.8 - 3.8 (1.3 - 2.8)
† K = 3dB measurement uncertainty
pA
‡ K = 3dB measurement uncertainty
wA
Installation and Lubrication
Size air supply line to ensure tool's maximum operating pressure (PMAX) at tool inlet. Drain condensate from valve(s) at low point(s) of piping,
air filter and compressor tank daily. Install a properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose
coupling without internal shut-off, to prevent hose whipping if a hose fails or coupling disconnects. See drawing 16590689 and table on page2.
Maintenance frequency is shown in a circular arrow and defined as h=hours, d=days, and m=months of actual use. Items identified as:
1. Air filter
2. Regulator
3. Lubricator
4. Emergency shut-off valve

Torque Adjustment

The most satisfactory adjustment is usually obtained by use of the tool on the actual application and increasing or decreasing the delivered
torque until the desired setting is reached. In any event, it is recommended that final adjustment be made by gradual progression.
Adjustable Clutch
1. Shut-off the air supply to the tool and rotate the adjustment cover to uncover the adjustment slot in the Clutch Housing. Rotate the spindle
until the hole in the adjustment nut is visible in the slot.
2. The tightening torque is adjusted by altering the tension of the Clutch Spring by means of the interlocking disc and the key provided.
3. When turning the key in clockwise rotation the torque is decreased, and when turning the key in counterclockwise rotation the torque is
increased. The rotation is indicated on the adjusting key.
Parts and Maintenance
When the life of the tool has expired, it is recommended that the tool be disassembled, degreased and parts be separated by material so that
they can be recycled.
The original language of this manual is English.
Tool repair and maintenance should only be carried out by an authorized Service Center.
Refer all communications to the nearest Ingersoll Rand Office or Distributor.
EN-2
Torque Range
(hard slam)
Style Clutch
Nm (lb-ft)
5. Hose diameter
6. Thread size
7. Coupling
8. Safety Air Fuse
Free
Speed
Output
90 psi
rpm
600 1/4" Quick Change
1000 1/4" Quick Change
1000 1/4" Quick Change
1000 1/4" Quick Change
1600 1/4" Quick Change
1600 1/4" Quick Change
Sound Level dB(A)
(ISO15744)
† Pressure(L ) ‡ Power(L
p
78.0
78.0
78.0
78.0
78.0
78.0
9. Oil
10. Grease - disassembly required
Vibration
Level
(ISO28927)
)
m/s
2
w
--- <2.5
--- <2.5
--- <2.5
--- <2.5
--- <2.5
--- <2.5
80182579_ed3