Cleaning And Lubrication; Required Maintenance At Ridgid Authorized Service Center; Accessories; Storage - RIDGID RE 6 Bedienungsanleitung

RE 6/RE 60 Electrical Tool

Cleaning And Lubrication

1. Wipe exterior of the electrical tool clean daily with a
clean dry cloth.
2. Clean the interior of the QCS coupling first by pointing
the opening towards the ground and gently shaking
any debris out. Then, visually inspect the area for any
debris. If needed, cotton swabs can be used to wipe
out any remaining debris. Do not force any material
into the pockets that hold the retaining balls.
3. The QCS coupling is lubricated for life at the factory
and does not require any further lubrication. Do not
add any lubricant to the QCS coupling.
Required Maintenance At RIDGID
Authorized Service Center
After 30,000 cycles, the electrical tool will show a blinking
yellow LED on the LED diagnostic display (Figure 2) as
long as the tool is turned ON to indicate that it is time for
maintenance and recalibration. The electrical tool will not
run if it is not serviced within 2,000 more cycles (32,000
total) after the yellow blinking LED begins.

Accessories

WARNING
The following tool accessories have been de signed
to function with the RE 6 and RE 60 Electrical
Tools. Other accessories suitable for use with other
tools may become hazardous when used on the
RE 6 and RE 60. To prevent serious injury, use only
accessories specifically designed and recom-
mended for use with the RE 6 or RE 60, such as
those listed below.
For a complete listing of RIDGID attachments
available for this tool, see the Ridge Tool Catalog
online at www.RIDGID.com or call Ridge Tool
Technical Service Department (800) 519-3456.
Catalog
No. Description
44693 18V 2.0Ah North & Latin America, Australia
44698 18V 4.0Ah North & Latin America, Australia
43458 120V Advanced Lithium Battery Charger
43333 230V Advanced Lithium Battery Charger
46823 RE 6 Carrying Case (Plastic)
43548 4P-6 4PIN™ Dieless Crimp Head
46798 SC-60B Scissor Cutter Head
46803 PH-60B Punch Head
43323 18V 2.0Ah Europe & China
43328 18V 4.0Ah Europe & China
47188 RE 60 Carrying Case (Plastic)
47193 LS-60B Latching Square Head
47198 LR-60B Latching Round Head
8
All listed batteries will work with any electrical tool. The dif-
ference between batteries from different regions is the
applied label(s).

Storage

Remove battery from tool and store electrical tool and bat-
tery in case. Avoid storing the electrical tool, batteries or
charger in extreme heat or cold. The electrical tool will not
turn ON if the tool or battery temperature is not within the
temperature range of 15°F (-10°C) to 122°F (50°C). So it
may be neces sary to allow the tool to warm or cool to a
temperature within the operating range by placing it in a
conditioned room before use. This will be indicated by a
red glowing LED on the LED diagnostic display.
Store the tool in the carrying case and
WARNING
place in a dry, secured area that is out of reach of children
and people unfamiliar with the RE 6/60 Electric Tool.
The electrical tool is dangerous in the hands of untrained
users.

Service And Repair

WARNING
Improper service or repair can make machine
unsafe to operate.
Service and repair on this RE 6/RE 60 Electrical Tool
must be performed by a RIDGID Authorized Press Tool
Service Cent er. The tool fasteners have been marked to
indicate if service has been performed by unauthorized
individuals.
For any repairs or maintenance, contact the Ridge Tool
Technical Service Department at (800) 519-3456 or
www.RIDGID.com for nearest authorized service outlet.
For information on your nearest RIDGID Authorized
Service Center or any service or repair questions:
• Contact your local RIDGID distributor.
• Visit www.RIDGID.com or www.RIDGID.eu to find
your local RIDGID contact point.
• Contact Ridge Tool Technical Service Department at
rtctechservices@emerson.com, or in the U.S. and
Canada call (800) 519-3456.
Disposal
Parts of the Electrical Tool contain valuable materials
and can be recycled. There are companies that specialize
in recycling that may be found locally. Dispose of the
com ponents in compliance with all applicable regula-