Electrical Safety; Residual Risks; Package Contents - DeWalt DW755 Bersetzt Von Den Originalanweisungen

EngLIsh
ʵ This electric tool complies relevant safety rules. Repairs
should only be carried out by qualified persons using
original spare parts; otherwise this may result in
considerable danger to the user.
Additional Safety Rules for Grinding and
Honing Machines
• Use only grinding and honing wheels carrying a label
stating the manufacturer, the type of bonding material,
the dimensions and the maximum speed of the wheel, and
complying with EN12413.
• Do not use grinding and honing wheels with a maximum
speed lower than the speed of the machine (see technical
data).
• Do not use grinding and honing wheels that do not conform
to the dimensions stated in the technical data. Do not use
any spacers to make a wheel fit onto the spindle.
• Replace a grinding or honing wheel as soon as it has worn by
more than ca. 40 mm.
• Always strictly follow the instructions when replacing a
grinding or honing wheel.
• Before fitting a new grinding or honing wheel, it must be
checked for cracks by suspending it on a thin cord and striking
it gently with a hammer. The wheel should produce a clear
sound. If not, the wheel is damaged and must not be used.
• Regularly check a grinding or honing wheel for alignment. If
the wheel is running out of centre or out of balance, it must
be replaced.
• Always store grinding and honing wheels in a dry place.
• Only use the machine at ambient temperatures from 5 °C to
40 °C.
• Switch on the machine and let the wheel run with no load for
at least 30 seconds before use.
• Always wear safety goggles when grinding dry.
• Never grind magnesium tools.

WARNING: Use of this machine can generate dust
containing chemicals known to cause cancer, birth
defects or other reproductive harm. Use appropriate
respiratory protection.

WARNING: Do not use the machine in the vicinity of any
highly inflammable materials.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.

Residual Risks

The following risks are inherent to the use of these machines:
• injuries caused by touching the rotating parts,
• injuries caused by disruption of the grinding wheel.
These risks are most evident:
• within the range of operation,
• within the range of the rotating machine parts.
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided.
22
These are:
• Impairment of hearing.
• Risk of accidents caused by the uncovered parts of the rotating
wheel or belt.
• Risk of injury when changing the wheel or belt.
• Risk of squeezing fingers when opening the guards.

Electrical Safety

The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D WALT tool is double insulated in accordance
e
with EN61029; therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
If an extension cable is required, use an approved 3–core
extension cable suitable for the power input of this tool (see
Technical Data).The minimum conductor size is 1.5 mm2; the
maximum length is 30 m.
When using a cable reel, always unwind the cable completely.

Package Contents

The package contains:
1 Grinding wheel
1 Honing belt
1 Clamping and grinding attachment
1 Water supply system
1 Plastic bag containing:
1 Spark guard
1 Spanner
1 Set of mounting material
1 Electrical scheme
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
WALT
e