Vitek VT-1618 R Die Betriebsanweisung Seite 5

2. Install the bowl (21).
3. Install the shaft (20) into the bowl.
4. Remove the protective cap (18) from the knife
(19) and install it on the shaft (20). If you need
additional knife, remove the protective cap (18)
from the additional knife (17) and install it on the
shaft (20) above the main knife (19).
4. Put some foodstuff into the bowl (21).
5. Cover the bowl (21) by the cap (23) with seal ring
(24) put on.
6. Turn the work head (2), and push on the head
from above to lock it in the on-position.
7. Insert the power cord plug into the wall outlet.
8. Turn the knob (3) to switch processor on, or turn
on pulse operating mode by pressing button
"PULSE" (4).
9. After finishing food processing switch the appli-
ance off by turning the knob to the "OFF" posi-
tion, and disconnect the power cord plug from
the wall outlet.
10. Press button (5), swivel work head (2) is lifted
and turned.
11. Remove the cap (23), take out the shaft (20)
with the knife (19) or with two knives attached,
extract the foodstuff from the bowl (21) by the
shovel (27).
Attention:
• Be careful while handling the knives. Be aware
of the sharp edges.
Using gratings/choppers and knives for cutting
potatoes for frying
1. Press button (5), swivel work head (2) is lifted
and turned.
2. Install the bowl (21).
3. Install the shaft (20) into the bowl.
4. Install the grating (8,9,12) you need, or chopper
(10,11), or knife for fine cutting potatoes for fry-
ing (13) on the disk-shaped holder (14).
Attention:
- use knife (15) installed on the disk-shaped hold-
er (16) for the rough cutting potatoes for frying.
5. Install disk-shaped holder (14 or 16) on the shaft
(20).
6. Cover the bowl (21) by the cap (23) with seal ring
(24) put on.
7. Turn the work head (2), and push on the head
from above to lock it in the on-position.
8. Insert the power cord plug into the wall outlet.
9. Turn the knob (3) to switch processor on, or turn
on pulse operating mode by pressing button
"PULSE" (4).
10. Put the foodstuff into the neck of the cap (23).
Use the pusher (22) to deliver the foodstuff.
Press on the pusher lightly to force the foodstuff
through the cap neck gradually.
1618.indd 5 1618.indd 5
11. After finishing food processing switch the appli-
ance off by turning the knob to the "OFF" posi-
tion, and disconnect the power cord plug from
the wall outlet.
12. Press button (5), swivel work head (2) is lifted
and turned.
13. Remove the cap (23), take out the shaft (20) with
the disk-shaped holder (14) attached, extract the
foodstuff from the bowl (21) by the shovel (27).
Making pastry
1. Press button (5), swivel work head (2) is lifted
and turned.
2. Install the bowl (21).
3. Install the shaft (20) into the bowl.
4. Install the nozzle (26) on the shaft (20).
5. Put all the pastry ingredients into the bowl (21).
14. Cover the bowl (21) by the cap (23) with seal ring
(24) put on.
15. Turn the work head (2), and push on the head
from above to lock it in the on-position.
16. Insert the power cord plug into the wall outlet.
17. Turn the knob (3) to switch processor on.
18. After finishing food processing switch the appli-
ance off by turning the knob to the "OFF" posi-
tion, and disconnect the power cord plug from
the wall outlet.
19. Press button (5), swivel work head (2) is lifted
and turned.
20. Remove the cap (23), take out the shaft (20) with
the nozzle (26) attached, extract the pastry from
the bowl (21) by the shovel (27).
Notice:
• Maximum amount of the pastry should not ex-
ceed 800 g.
• Start making the pastry at the low speed, in-
crease the speed gradually.
• The processor should be in use no longer then
20-30 sec, after that the brake should be made
for about 2 minutes.
• Do not take the pusher (22) out of the neck of
the cap (23) while making the pastry. Otherwise
the particles of flour would fly out of the neck of
the cap (23).
Beating
1. Press button (5), swivel work head (2) is lifted
and turned.
2. Install the bowl (21).
3. Install the shaft (20) into the bowl.
4. Install the nozzle (25) on the shaft (20).
5. Put all ingredients you need into the bowl (21).
6. Cover the bowl (21) by the cap (23) with seal ring
(24) put on.
7. Turn the work head (2), and push on the head
from above to lock it in the on-position.
5 5
ENGLISH
03.05.2007 11:56:58 03.05.2007 11:56:58