Noise/Vibration Information; Changing The Tool - Bosch GSB 162-2 RE Professional Originalbetriebsanleitung

14 | English
Impact drill
– Second gear
Rated speed
– First gear
– Second gear
Impact rate at no-load speed
– First gear
– Second gear
Spindle collar diameter
Max. drilling diameter (first/second gear)
– Concrete
– Masonry
– Steel
– Wood
Chuck capacity
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise/vibration information

Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 97 dB(A); sound power level
108 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1:
2
Drilling into metal: a = 6.0 m/s , K = 1.5 m/s
h
Impact drilling into concrete: a = 23.0 m/s
h
2
Screwdriving: a < 2.5 m/s , K = 1.5 m/s
h
2
Thread cutting: a < 2.5 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
1 609 92A 57X | (30.09.2019)
Implement additional safety measures to protect the oper-
GSB 162-2 RE
ator from the effects of vibration, such as servicing the
-1
min 0–1800
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
-1
min 555
Assembly
-1
min 1 300
u
-1
min 12 750
-1
min 30 600
Auxiliary handle (see figure A)
mm 53
u
mm 82/82
You can adjust the auxiliary handle (10) to any of 12 posi-
mm 162/82 tions in order to achieve a safe work posture that minimises
fatigue.
mm 20/14
Turn the lower gripping end of the auxiliary handle (10) in
mm 50/32
rotational direction ➊ and push the auxiliary handle (10) for-
mm 3–16
ward until you can swivel it into the required position. Then
pull the auxiliary handle (10) back again and turn the lower
kg 4.8
gripping end in rotational direction ➋ to tighten it.
/ II
Setting the Drilling Depth
You can use the depth stop (7) to set the required drilling
depth X.
Loosen the wing bolt for adjusting the depth stop (9) and in-
sert the depth stop into the auxiliary handle (10).
Pull the depth stop far enough out that the distance between
the drill bit tip and the edge of the depth stop corresponds
to the required drilling depth X.
Retighten the wing bolt for adjusting the depth stop (9).

Changing the Tool

u
2
2 2
, K = 3.0 m/s Keyed chuck with automatic lock (see figure D)
2
Open the keyed chuck (1) by turning it until the tool can be
inserted.
2
Insert the tool. Insert the drill chuck key (12) into the corres-
ponding holes of the keyed chuck (1) and clamp the tool
evenly.
Keyed Chuck with Manual Lock (see figure E)
Open the keyed chuck (16) by turning it until the tool can be
inserted. Insert the tool.
Insert the chuck key (15) into the corresponding holes of the
keyed chuck (16) and clamp the tool evenly.
With the hexagon of the chuck key (15), turn the eccentric
cam as far as it will go in rotational direction ➋. This ensures
sufficient tensioning force.
To remove the application tool, turn the eccentric cam in ro-
tational direction ➊ and open the keyed chuck (16) with the
chuck key (15).
Pull the plug out of the socket before carrying out any
work on the power tool.
Do not operate your power tool without the auxiliary
handle (10).
Wear protective gloves when changing tools. The drill
chuck may heat up significantly when it is used for long
periods.
Bosch Power Tools