Preparation For Operation - GRAPHITE 59G321 Betriebsanleitung

TRANSLATION OF
THE ORIGINAL INSTRUCTIONS
FINISHING SANDER
59G321
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
When sanding wood and metal surfaces coated with paints with
lead additives, harmful or toxic dust may appear. Contact or
inhalation of such dust may endanger operator's or other persons'
health. Use appropriate personal protection measures such as filter
masks and safety glasses. Use dust extraction system.
PRIOR TO SANDER OPERATION
• During operation hold the sander firmly with both hands.
• Ensure the sanding paper does not touch processed material prior
to switching the sander on.
• Ensure the abrasive paper is well installed and paper clamping
levers are in locking position before switching the sander on.
• Do not touch moving parts of the sander.
• After switching off, do not put away the sander until all moving
parts stop.
• Use protective mask if the dust appears during sanding. Dust,
which appears when sanding surfaces coated with lead-based
paint, some types of wood and metal, is harmful.
• Pregnant women and children should not enter the room where
lead-based paint is removed with the use of sander.
• Do not eat, drink or smoke in the room where lead-based paint is
removed with the sander.
• Avoid using long extension cords.
WHEN OPERATING THE SANDER
• When using the sander, always wear earmuff protectors and
protection half-mask.
• Sander is not designed for wet operation.
• Ensure the switch is in the OFF position before plugging the
sander to a power supply.
• Keep the power cord away from moving parts of the sander.
• Use safety goggles or glasses when operating the sander above
head.
• When operating the sander do not apply excessive pressure that
might stop the tool.
CAUTION! This device is designed to operate indoors.
The design is assumed to be safe, protection measures and
additional safety systems are used, nevertheless there is always a
small risk of operational injuries.
CONSTRUCTION AND USE
Finishing sander is a hand-held power tool driven by a single-phase
commutator motor. Due to a proper insulation there is no possibility
to touch any metal parts that accidentally might be live. The sander
does not require earth lead (insulation class II). Finishing sander is
designed for surface sanding of wood products, polishing wood
surfaces with lacquer coating, fine polishing of lacquered metal
surfaces, removal of rust or specks of lacquer before applying new
lacquer, finishing of concrete surfaces etc. Range of use covers repair
and building works, woodworking and any work from the scope of
individual, amateur activities (tinkering).
Do not use the sander for sanding surfaces that contain
magnesium or asbestos, or covered with gypsum.
DESCRIPTION OF DRAWING PAGES
Below enumeration refers to the device elements depicted on the
drawing pages of this manual.
Switch
1.
Switch lock button
2.
Dust outlet
3.
Dust suction adaptor
4.
Sanding paper clamping lever
5.
Sander backing pad
6.
Holes for dust extraction
7.
* Slight differences may appear between the product and the drawing
MEANING OF SYMBOLS
CAUTION
WARNING
ASSEMBLY/SETTINGS
INFORMATION
EQUIPMENT AND ACCESSORIES
Dust suction adaptor
1.
Sanding paper
2.

PREPARATION FOR OPERATION

CHOOSING SANDING PAPER
Coarse-grained sanding paper is generally used for coarse
processing of most materials, while fine-grained paper is used for
finishing works.
• When the surface is not flat, start the work with coarse-grained
sanding paper and continue until the surface is flat.
• Next use middle-grained paper to remove traces of coarse
processing.
• To finish the work use fine-grained sanding paper.
INSTALLATION OF SANDING PAPER
Disconnect the power tool from power supply.
• Select sanding paper gradation appropriate for the planned task.
• To soften the paper, rub its smooth side against an edge, for
instance of a tabletop.
• Loosen sanding paper clamps (5) (fig. A).
• Fix the sanding paper to the sander backing pad (6).
• Ensure that the holes on the sanding paper (8) and backing pad
(6) fully match (fig. B).
• Bend both ends of the sanding path on the sander backing pad
edges.
• Tighten sanding paper clamps (5) (fig. C).
• Ensure the sanding paper is installed properly.
Sanding paper must adhere to the sander backing pad. There
must be no slack. If the paper stretches during sanding, remove
the slack. It will significantly prolong the lifetime of the sanding
paper.
DUST EXTRACTION
Use perforated sanding paper, so the dust can reach extraction hole
through the backing pad.
• You can connect a dust extraction (for instance vacuum cleaner),
with the use of the adaptor (4).
• Insert the adaptor (4) into dust outlet (3) (fig. D).
• Connect with dust extraction system.
9
- 1 pce
- 1 pce