Werbung
Remove the rubber blades from the squeegee
body.
To assemble the new blades, place the metal bar
holders on the front blade; place them on the
squeegee body and insert the bolts in the holes of
the squeegee body.
Place the rear blade on the squeeegee body with
the the bolts in its holes; place the metal bar hold-
ers and block the blades screwing the fixing knobs
( Photo G - 7 ).
It's normal that the rear strap has to be extended
to centre the connection screws. This will bring
it under the correct tension to avoid folds on the
floor and dry correctly.
7.2.4
SQUEEGEE ADJUSTMENT
The knob screw on the squeegee support (Photo
G - 6 ) adjust the squeegee's inclination with re-
spect to the floor. The two screws on the sides,
connected to the rear wheels of the squeegee
(Photo G - 2 ), are to adjust the pressure of the
squeegee to the floor.
When the squeegee is perfectly adjusted, the rear
squeegee blade, sliding as it moves, bends in all
points forming an angle of 45° with the floor.
As the machine operates (advances), it is possible
to operate on the inclination knob and pressure
screws ( Photo G - 6; Phot G - 2 ) to adjust the in-
clination and pressure of the squeegee blades on
the floor.
Squeegee drying must be uniform along the en-
tire drying line: damp patches mean that drying
is in- sufficient; turn the adjustment knobs to op-
timise drying.
7.2.5
SPLASH GUARD ASSEMBLY/DISAS-
SEMBLY
The splash guard is assembled to the brush plate
with a spring holder linked to the brush plate itself.
To disassemble the splash guard simply detach the
spring holder and pull the splash guard.
To reassemble, fix the splash guard in the brush
plate, and then hook the steel cable to one side of
the plate and the spring holder to the other side
of the brush plate.
7.3
ACCESSORY ASSEMBLY/DISASSEM-
BLY (BRUSHES, PAD DRIVERS AND ABRASIVE
DISKS)
• Never use the machine if brushes or pad drivers
and abrasive disks are not perfectly installed.
Assembly:
Make sure that the brush plate is raised; otherwise
lift it by following the instructions provided in the
specific section.
Make sure that the ignition key on the control
panel is in position "0".
Bring the brushes (or the guide disks equipped
with abrasive disks) near the connections, under
the brush plate; lift them, bring them through
the centering flange, and turn them opposite the
rota- tion direction until you hear the stable "click"
con- nection.
•Do not allow the length of the rows of brushes
to become lower than 1 cm.
•Do not allow the thickness of the abrasive disks
to become less than 1 cm.
Working with excessively worn brushes or exces-
sively thin abrasive disks may damage the ma-
chine and the floor.
Regularly check the wear on these parts before
starting to work.
Disassembly or replacement:
Make sure that the brush plate is raised; otherwise
lift it by following the instructions provided in the
specific section.
Make sure that the ignition key on the control
panel is in position "0".
While holding the brushes (or the guide disks) with
the hands under the plate, turn them in the rota-
tion direction while lowering to release them from
the guide plate.
7.4
FILLING AND DRAINING THE DETER-
GENT SOLUTION TANK
☞ The temperature of the water or the deter-
gent should never exceed 50°C.
☞ AAlways empty the detergent solution tank be-
fore filling it up.
To fill the solution tank:
• Remove the plug in the back of the machine.
• Leave 7 cm between the mouth of the plug and
the liquid level. Do not fill beyond this point!
• Add the required quantity of the chemical prod-
uct, considering the percentage indicated by
the supplier, with reference to the full tank ca-
pacity listed on the product sheet.
• Use only those products suitable for the floor
and the dirt to be removed.
•The machine was designed to be used with non-
foaming and biodegradable deter- gents made
specifically for scrubber-driers. The use of other
chemical products (such as sodium hypochlo-
rite, oxidisers, solvents or hydrocarbons) may
damage or destroy the machine.
• Follow the safety regulations specified in the
relative section and indicated on the detergent
container.
• Contact the machine manufacturer to obtain
a complete list of available and suitable deter-
gents.
• •Always add the detergent after filling the tank
with water to prevent foam from being created
in- side.
35
Werbung
Kapitel
