Makita HR2450 Betriebsanleitung Seite 7

Bit angle (when chipping, scaling or demolishing)
CAUTION:
Always be sure that the tool is switched off and
unplugged before changing the bit angle.
The bit can be secured at the desired angle. To change
the bit angle, depress the lock button and rotate the
action mode changing knob to the O symbol. Turn the
bit to the desired angle. (Fig. 5)
Depress the lock button and rotate the action mode
changing knob to the g symbol. Then make sure that
the bit is securely held in place by turning it slightly.
(Fig. 6)
Depth gauge (Fig. 7)
The depth gauge is convenient for drilling holes of uni-
form depth. Loosen the side grip and insert the depth
gauge into the hole in the side grip. Adjust the depth
gauge to the desired depth and tighten the side grip.
NOTE:
The depth gauge cannot be used at the position where
the depth gauge strikes against the gear housing.
Switch action (Fig. 8)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop. For continuous opera-
tion, pull the switch trigger and then push in the lock but-
ton. To stop the tool from the locked position, pull the
switch trigger fully, then release it.
Lighting up the lamps
For model HR2450F/HR2450FT
CAUTION:
Do not look in the light or see the source of light directly.
To turn on the lamp, pull the trigger. Release the trigger
to turn it off.
NOTE:
Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower the
illumination.
Reversing switch action (Fig. 9)
This tool has a reversing switch to change the direction of
rotation. Move the reversing switch lever to the
tion (
A side) for clockwise rotation or the
(
B side) for counterclockwise rotation.
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• When you operate the tool in counterclockwise rotation,
the switch trigger is pulled only halfway and the tool
runs at half speed. For counterclockwise rotation, you
cannot push in the lock button.
(Fig. 8)
D
E
Changing the tool holder
For model HR2450T/HR2450FT
The tool holder can be easily exchanged for the drill
chuck assembly.
Removing the tool holder (Fig. 10)
Before removing the tool holder, always remove the bit.
Grasp the change cover of the tool holder and turn in the
direction of the arrow until the change cover line moves
from the
the direction of the arrow.
Attaching the drill chuck assembly (Fig. 11)
Check the line of the drill chuck assembly shows the
symbol. Grasp the change cover of the drill chuck assem-
bly and set the line to the
Place the drill chuck assembly on the spindle of the tool.
Grasp the change cover of the drill chuck assembly and
turn the change cover line to the
can clearly be heard.
Selecting action mode
Rotation with hammering (Fig. 12)
For drilling in concrete, masonry, etc., depress the lock
button and rotate the action mode changing knob to the
H symbol. Use a tungsten-carbide tipped bit.
Hammering only (Fig. 13)
For chipping, scaling or demolition operations, depress
the lock button and rotate the action mode changing
knob to the g symbol. Use a bull point, cold chisel, scal-
ing chisel, etc.
Rotation only (Fig. 14)
For drilling in wood, metal or plastic materials, depress
the lock button and rotate the action mode changing
knob to the m symbol. Use a twist drill bit or wood bit.
CAUTION:
• Do not rotate the action mode changing knob when the
tool is running under load. The tool will be damaged.
• To avoid rapid wear on the mode change mechanism,
be sure that the action mode changing knob is always
positively located in one of the three action mode posi-
tions.
Torque limiter
The torque limiter will actuate when a certain torque level
is reached. The motor will disengage from the output
shaft. When this happens, the bit will stop turning.
CAUTION:
posi-
• As soon as the torque limiter actuates, switch off the
position
tool immediately. This will help prevent premature wear
of the tool.
• Hole saws cannot be used with this tool. They tend to
pinch or catch easily in the hole. This will cause the
torque limiter to actuate too frequently.
symbol to the symbol. Pull forcefully in
symbol.
symbol until a click
7