Taurus Alpatec RCMB25 Bedienungsanleitung Seite 14

USE:
- Unroll the cable completely before plugging it in.
- Connect the appliance to the mains.
- Turn the appliance on, by using the on/off switch
(G) located on the bottom of the appliance.
- The appliance will enter standby mode and "0"
will appear on the screen.
CONTROL PANEL SET UP:
- Turn the appliance on, by using the function but-
ton (a). The appliance will enter into fan mode
and "--" will appear on the screen.
- Press function button (a) again to select the
heat intensity:
- - I: 1000W heating
- - II: 2000W heating
- During the device working (I or II intensity),
press the (b) button to set the timer so that
when it reaches the desired time, the appliance
will switch off.
- Keep pressing this button to select the hours
until you reach the desired time. After setting
time, the display will show current setting time
for 5 seconds, then it will resume to previous
display, meanwhile the light of the clock symbol
will turn on.
- If the device is in standby mode "--", it can be
programmed to turn on at the desired time (1-
12h). Press the button (b) and select the hours.
The light on the clock symbol will light up. At the
end of the time, the appliance will turn on auto-
matically at the temperature of 23ºC by default.
- The product automatically turns off after 12h of
operation.
REMOTE CONTROL SET UP:
- Turn the appliance on, by using the function
button (I). The appliance will enter into fan mode
and "--" will appear on the screen.
- Press the (IV) button to select the heat intensity:
- I: 1000W heating
- II: 2000W heating
- During the device working (I or II intensity),
press the (II) button to set the timer so that
when it reaches the desired time, the appliance
will switch off.
- Keep pressing this button to select the hours
until you reach the desired time. After setting
time, the display will show current setting time
for 5 seconds, then it will resume to previous
display, meanwhile the light of the clock symbol
will turn on.
- If the device is in standby mode "--", it can be
programmed to turn on at the desired time (1-
12h). Press the button (II) and select the hours.
The light on the clock symbol will light up. At the
end of the time, the appliance will turn on auto-
matically at the temperature of 23ºC by default.
- The product automatically turns off after 12h of
operation.
TIME/DAY SET UP:
- To set the current time, press the button (III) and
then press the + (VII) or - (V) button according
to the desired time.
- Press the button (III) again to set the minutes.
Repeat the same action for days (d1-d7).
- Press OK (VI).
TEMPERATURE SET UP
- During the device working, select + / - to select
the temperature (10-49ºC). The display shows
20ºC by default.
- Press OK to confirm it.
WEEKLY PROGRAM SET UP
- After setting the time, press the on/off button (I)
to enter the operating mode.
- Press the (X) button to enter the weekly pro-
gram settings.
- Press the days setting button (IX) and set the
desired day (d1-d7).
- Press the edit button (XII) to set the periods
(P1-P6).
- Press the (XI) button to select the start time of
the device.
- Press the (XIII) button to select the end time of
the device.
- Press +/- to select the desired temperature in
the weekly configuration. Press OK to confirm.
- To cancel the weekly program, press the (X)
button.
WINDOW SENSOR SET UP
- Press the on/off button (I) to enter the operating
mode.
- Press the window sensor button (VIII). The
default temperature is 23ºC. Press +/- to set the
desired temperature.
- When the window sensor mode, if the room
temperature decreases 5-10ºC in 10 minutes,