Atlantic CMG-PACK0 Bedienungsanleitung Seite 9

Day of week and time – When entered the menu «Settings», the appliance displays the menu «Day of week
and time». The parameter «d»/«1» (day of week) is blinking on the screen, to change the day use the buttons
and , where «1» is Monday, and «7» is Sunday. Press the button
switch to hour setting. The parameter «HH»/«12» is blinking on the screen, use the buttons
the hour from 0 to 23. Press the button
parameter «ПП»/«00» is blinking on the screen, use the buttons
Press the button to finalize minutes settings and to switch to the menu «Dayly programming (P6)».
Dayly programming (P6) – After carrying out the day of week and time settings, the appliance switches
automatically to the menu «Dayly programming». The parameter «P6»/«no» is blinking on the screen and if you
select this parameter by pressing the button
menu «Weekly programming». To enter the menu «Dayly programming», select the parameter «P6»/«go» by
using the buttons ,
screen where «00» is the hour and «Ес» is the «ECO» mode. To change the parameter from «Ес» to «Со»
(«Comfort» mode), use the buttons
hour from 00 to 23. After adjusting the last hour, the parameter «P6»/«no» is blinking on the screen. Press the
button to validate the program «Р6» and to switch to the menu «7d».
Weekly programming (7d) – After the menu «Dayly programming (P6)», the appliance switches automatically
to the menu «Weekly programming». The screen displays the blinking parameter «7d»/«no» and if you select
this parameter by pressing the button
«Open window fucntion». To enter the menu «Weekly programming», select the parameter «7d»/«go» by using
the buttons , and validate by pressing the button
where «d1» is the day of week and «P1» is the preset program. To change the program from «Р1» to «Р6»,
use the buttons ,
«d1» to «d7». After setting the last day, the parameter «7d»/«no» is blinking on the screen. Press the button
to validate the weekly program «7d» and to switch to the menu «Open window function».
Open window function – After the menu «Weekly programming (7d)», the appliance automatically switches to
the menu «Open window function». The parameter «][»/«oF» is blinking on the screen and if you select this
parameter by pressing the button
menu «Settings». To activate the «Open window fucntion», select the parameter «][»/«on» by using the buttons
, and validate by pressing the button
Note: if the apppliance detects an open window in the room where it is installed, the appliance stops heating
and the screen displays the parameter «][» (blinking). To go on with heating, you should manually select the
parameter «][»/«go» on the appliance by using the buttons
To exit the settings menu – Press the button
The parameter «no» is blinking on the screen, select this parameter by pressing the button
appliance to return to the «Comfort» mode.
Note: After 60 seconds with no activity in any «Settings» menu, the appliance will automatically exit this
menu and will go back to the «Comfort» menu.
CONTROL LOCK
To prevent changing the settings by a third person, you can lock the controls. Simultaneously press and hold
down the buttons and
buttons and (for over over 5 seconds).
Note: when the appliance is locked, the screen displays the ambient temperature.
CALIBRATING THE APPLIANCE
To match the actual temperature (in the room) to the temperature displayed, you can calibrate the appliance.
Simultaneously press and hold down the buttons
(default 0.0°С). By pressing the buttons
simultaneously press and hold down the buttons
Note: if no button is pressed for 5 seconds or more, the appliance quits calibration mode automatically.
and validate by pressing the button
, and validate by pressing the button
, the appliance skips the «Weekly programming» and goes to the menu
and validate by pressing the button
, the appliance skips the menu «Open window function» and switches to the
(for over over 5 seconds). To unlock the appliance also press and hold down the
to validate hour settings and to switch to minute settings. The
, the appliance skips the «Dayly programming» and goes to the
. The parameter «00»/«Ес» is blinking on the
. The parameter «d1»/«P1» is blinking on the screen,
. Repeat the operation for each day of week from
.
,
repeatedly until the indicator below the pictogram
, and . The screen displays the current offset value
and , change this value from -3°С to +3°С. To quit calibration,
, and . The appliance returns to the current mode.
to validate the day of week and to
and , to change the minutes from 0 to 59.
. Repeat the operation for each
and validate by pressing the button
EN
and to change
.
. ights up.
to enable the
9