Herunterladen Inhalt Inhalt Diese Seite drucken

Nikko Air AIR ELITE 115 Handbuch Seite 30

Inhaltsverzeichnis

Werbung

CONNECTING THE CONTROLLER TO THE SIMULATOR:
EN
1. Turn on the power of the drone and the controller.
2. Push "B" for 5 seconds until you feel vibration in the remote and the drone turns o .
3. Turn ON the drone. The LED light should be fading in and out .
4. Using the USB charging cord, plug the USB into the computer and insert the charging port to the drone.
5. Follow the instructions in the simulator to nish the setup.
6. To switch back to ying mode push "B" for 5 seconds until the drone turns o . Turn on the drone.
RACCORDEMENT DU DISPOSITIF DE COMMANDE AU SIMULATEUR:
FR
1. Mets sous tension le drone et la radiocommande.
2. Appuie sur la touche « B » pendant 5 secondes jusque ce que tu ressentes des vibrations dans la radiocommande et que le drone
soit mis hors tension.
3. Allume le drone. Le voyant LED devrait s'allumer et s'estomper progressivement.
4. À l'aide du cordon de charge USB, branche la che USB à l'ordinateur, puis insère dans le port de charge du drone.
5. Suis les instructions du simulateur pour terminer la con guration.
6. Pour revenir en mode Pilotage, appuie sur la touche « B » et maintiens-la enfoncée pendant 5 secondes jusqu'à ce que le drone
s'
teigne. Allume le drone.
é
CONTROLLER MIT SIMULATOR VERBINDEN:
DE
1. Verwenden Sie das USB-Ladekabel. Verbinden Sie das USB-Kabel mit dem Computer und mit dem Ladeanschluss an der Drohne.
2. Schalten Sie die Drohne und den Controller ein.
3. Drücken Sie die Taste „B" 5 Sekunden lang, bis Sie eine Vibration in der Fernbedienung verspüren und die LED der Drohne anfängt
schnell zu blinken.
4. Schalten Sie die Drohne AUS und EIN. Die LED-Anzeige sollte sich ein- und ausschalten.
5. Folgen Sie den Anleitungen des Simulators, um den Setup zu beenden.
6. Schalten Sie in den Flugmodus zurück, indem Sie die Taste „B" 5 Sekunden lang gedrückt halten, bis die Rücklichter der Drohne
blinken. Schalten Sie die Drohne ein und aus.
CONECTAR EL CONTROL AL SIMULADOR:
ES
1. Usando el cable de carga USB, conecte el USB en el ordenador e introduzca el puerto de carga en el dron.
2. Conecte la alimentación del dron y el control.
3. Pulse "B" durante 5 segundos hasta que sienta una vibración en el mando y las LED del dron comiencen a parpadear rápidamente.
4. APAGUE y ENCIENDA el dron. La luz LED deberá aparecer y desaparecer.
5. Siga las instrucciones en el simulador para nalizar la con guración.
6. Para volver al modo vuelo, pulse "B" durante 5 segundos hasta que las luces traseras del dron estén parpadeando. Apague y
encienda el dron.
CONNETTERE IL CONTROLLER AL SIMULATORE:
IT
1. Usando il cavo di carica USB, inserire l'USB nel computer e la porta di ricarica sul drone.
2. Accendere il drone e il controller.
3. Premere "B" per 5 secondi nché non si percepisce vibrazione nel telecomando e il LED del drone inizia a lampeggiare
rapidamente.
4. Spegnere e accendere il drone. Le luce LED dovrebbe accendersi e spegnersi aumentando e diminuendo gradualmente l'intensità.
5. Seguire le istruzioni nel simulatore per completare l'impostazione.
6. Per tornare alla modalità di volo, premere "B" per 5 secondi nché le luci posteriori del drone lampeggiano. Accendere e spegnere
il drone.
LIGAR O CONTROLADOR AO SIMULADOR:
PT
1. Utilizando o cabo de carregamento USB, ligue o USB ao computador e insira a porta de carregamento no drone.
2. Ligue a alimentação do drone e do controlador.
3. Prima "B" durante 5 segundos até sentir a vibração no remoto e o LED do drone começar a piscar rapidamente.
4. Desligar e Ligar o drone.A luz LED deve estar a aumentar e diminuir de intensidade.
5. Siga as instruções no simulador para concluir a con guração.
6. Para voltar ao modo de voo, prima "B" durante 5 segundos até que as luzes traseiras do drone quem intermi tentes.Ligar e
desligar o drone.
DE CONTROLLER OP DE SIMULATOR AANSLUITEN:
NL
1. Sluit de USB-kabel aan op de computer en steek het ander uiteinde in de laadaansluiting van de drone.
2. Schakel de drone en de controller in.
3. Druk 5 seconden op "B" totdat de afstandsbediening trilt en de LED op de drone snel knippert.
4. Schakel de drone uit en opnieuw in. Het LED-lampje moet in- en uitfaden.
5. Volg de instructies in de simulator om het instellen af te ronden.
6. Om opnieuw naar de vliegmodus te schakelen, druk 5 seconden op "B" totdat de achterlichten van de drone knipperen. Schakel
de drone in en uit.
ŁĄCZENIE STEROWNIKA Z SYMULATOREM:
PL
1. Kabel ładowania USB podłączyć do portu USB w komputerze i portu ładowania w dronie.
2. Włączyć zasilanie drona i sterownika.
3. Wcisnąć na 5 sekund przycisk „B", aż poczujesz wibracje zdalnego sterownika i dioda LED na dronie zacznie szybko migać.
4. WYŁĄCZYĆ drona i WŁĄCZYĆ. Dioda LED powinna rozświetlać się i przygasać.
5. Postępować zgodnie z instrukcjami, podawanymi w symulatorze, aby zakończyć kon gurację.
6. Aby wrócić do trybu latania, ponownie wcisnąć na 5 sekund przycisk „B", aż tylne światła drona zaczną migać. Włączyć drona i
wyłączyć.
17

Werbung

Inhaltsverzeichnis
loading

Verwandte Produkte für Nikko Air AIR ELITE 115

Diese Anleitung auch für:

Air elite 115 race set

Inhaltsverzeichnis