Window Meanings - Varian 969-8988 Bedienungshandbuch

Examples:
Command: START
Source: PC
Destination: Controller
02 80 30 30
STX ADDR WINDOW
Source: Controller
Destination: PC
02 80 06 03
STX ADDR ACK ETX
Command: STOP
Source: PC
Destination: Controller
02 80 30 30
STX ADDR WINDOW
Source: Controller
Destination: PC
02 80 06 03
STX ADDR ACK ETX
Command: SOFT-START (ON)
Source: PC
Destination: Controller
02 80 31 30
STX ADDR WINDOW
Source: Controller
Destination: PC
02 80 06 03
STX ADDR ACK ETX
Command: SOFT-START (OFF)
Source: PC
Destination: Controller
02 80 31 30
STX ADDR WINDOW
Source: Controller
Destination: PC
02 80 06 03
STX ADDR ACK ETX
Command: READ PUMP STATUS
Source: PC
Destination: Controller (with address = 3)
02 83 32 30
STX ADDR WINDOW
Source: Controller (with address = 3 in stop status)
Destination: PC
02 83 32 30 35 30 30 30 30 30 30 03
STX ADDR WINDOW DATA (STATUS)
Command: READ SERIAL TYPE
Source: PC
Destination: Controller (with address = 3 in 485 mode)
02 83 35 30
STX ADDR WINDOW
Source: Controller
Destination: PC
02 83 35 30 34
STX ADDR WINDOW
30 31 31 03 42
WR ON ETX
38 35
CRC
30 31 30 03 42
WR OFF ETX
38 35
CRC
30 31 31 03 42
WR ON ETX
38 35
CRC
30 31 30 03 42
WR OFF ETX
38 35
CRC
35 30 03 38 37
RD ETX CRC
38
ETX CRC
34 30 03 38 31
RD ETX CRC
30 31 03 42
RD DATA ETX CRC

Window Meanings

N. Read/
Write
33
000 R/W
CRC
001 R/W
008 R/W
32
CRC
100 R/W
101 R/W
32
CRC
102 R/W
103 R/W
33
CRC
104 R/W
105 R/W
106 R/W
37
107 R/W
108 R/W
30
109
83
TECHNICAL INFORMATION
Data Description
Type
L Start/Stop
(in
remote/Front
mode the
window is a
read only)
L Low Speed
Activation
L Remote
(default) or
Serial
configuration
L Soft Start
(write only
in Stop
condition)
N R1 Set Point
type
N R1 Set Point
valve
(expressed in
Hz, W or s)
N Set Point
delay: time
between the
pump start and
the set point
check
(seconds)
L Set Point
signal
activation type:
the signal can
be "high level
active" or "low
level active"
N Set point
hysteresis
(in % of value)
L Water cooling
L Active Stop
(write only in
stop)
N Baud rate
W L Pump life/
cycle time/
cycle number
reset
Admitted
Values
Start = 1
Stop = 0
No = 0
Yes = 1
(default = 0)
Remote = 1
Serial = 0
(default = 1)
YES = 1
NO = 0
0 = Frequency
1 = Power
2 = Time
3 = Normal
4 =Pressure
(default = 3)
(default = 867)
0 to 99999
(default = 0)
0 = high level
active
1 = low level
active
(default = 0)
0 to 100
(default = 2)
0 = NO
1 = YES
0 = NO
1 = YES
600 = 0
1200 = 1
2400 = 2
4800 = 3
9600 = 4
(default = 4)
To reset write '1'
87-900-986-01 (C)