Felisatti WG130/1300VE Bedienungsanleitung Seite 4

WARNING! Do not use the machine without the
protection devices.
WARNING! Do not grind material containing
amianthus.
Working with materials containing amianthus/
asbestos and/or silica stones produces a dust, which
is harmful to health. Protect yourself from inhaling
this dust, in compliance with current regulations on
accident prevention.
Do not let children use the machine.
For your personal safety, always connect the
machine to a mains supply protected by a differential
and thermal cutout switch, in accordance with
regulations on low-voltage wiring sitemaps.
Do not pierce the motor housing as this could
damage the double insulation (use adhesive labels).
Check the work area with a metal detector for
hidden wires, gas and/or water pipes.
Always unplug the machine before carrying out
work on it.
Always stop the machine by switching it off, not
by unplugging it.
WARNING! For security reasons it is essential to
control that the differential is working properly before
beginning to work. Repair or change the damaged
differential only by qualified repair personnel.
WARNING! Before each use, inspect the plug
and lead. Should they need replacing, have this
done by an official service centre.
In case the cable gets damaged or breaks
during work session, do not touch it, but disconnect
the plug from power source. Never use the machine
with a damaged cable.
Keep the mains lead clear of the working range
of the machine.
Only plug the machine in when it is switched off.
Always use the machine with the auxiliary
handle attached.
Hold the machine firmly in both hands and in a
stable position.
Use only grinding accessories whose admissible
revolutions are at least the same that the device's
noload revolutions.
Ensure that the grinding accessory dimensions
are correct for the size of the grinder.
The abrasive discs should be handled and
kept with the utmost care, in accordance with the
manufacturer's instructions.
Protect grinding accessory from knocks, blows
and grease.
Check grinding accessory carefully before use
to make sure it is not damaged or cracked. Replace
cracked or damaged discs immediately.
Make sure the grinding accessories are fitted in
accordance with the manufacturer's instructions.
Check that the grinding accessory has been
properly fitted and secured before using the
machine. Start the machine with no load and run for
4
30 seconds in a safe position; if you notice serious
vibration or any other defect stop the machine
immediately. This may be a sign of incorrect fitting or
a badly balanced grinding accessory.
Use only clamps or plates specified for this tool.
Do not use separate bushings or adapters to adapt
grinding accessories with large holes.
In machines designed to be used with
accessories with threaded holes, check that the
thread on the disc is long enough to take the length
of the spindle.
Ensure that the part to be worked on is firmly
secured before beginning any operation.
Do not fix tool in a bench screw.
For trimming, the angle formed by the disc and
the work surface should be approximately 30 to 40
degrees for optimum results.
Bring the tool near the work piece only when
connected.
Beware of shavings that fly off. Hold the tool that
so that sparks fly away from you or other people and
inflammable materials.
When working on stone, use dust extraction
equipment and wear a mask. The vacuum must be
authorised to extract stone dust.
When working with the machine, always wear
safety goggles and ear protection. Other personal
protection equipment such as dust masks, gloves,
helmet and apron should be worn when necessary,
along with nonslip safety footwear. A dust mask is
required when the dust from the material deburred,
such as paint or other coating, is harmful. If in doubt,
use safety equipment.
Make sure the vents are free when working
with dust. If they require cleaning, first unplug
the machine, do not use metal objects and avoid
damaging internal parts.
Keep hands away from rotating parts.
Do not touch the grinding tools when rotating.
WARNING! The grinding accessory keeps
moving for a long time after the machine has been
switched off.
In case of power cut or when disconnecting
corddirectly from power supply, depress immediately
the On-/off switch and place it in the "Off" position,
thus avoiding accidental starting.
Connect those tools used outdoors by means of
an adjusted differential to a shooting power supply of
maximum 30 mA. Use authorised extension cables
to work outdoors.
Residual risks
Even when the power tool is used as
prescribed it is not possible to eliminate
all residual risk factors. The following hazards may
arise in connection with the power tool's construction
and design:
- Damage to lungs if an effective dust mask is not