Positions Of The Handle; Car Installation; Initial Configuration Of The Harness Straps And Shoul- Der Pads - Chicco AUTO-FIX FAST Gebrauchsanleitung

M. Buttons to rotate the carry handle
N. Clik Clak pins (to fasten it to the stroller)
Diag. 4 (Back)
O. Release handle (from the base and the
stroller)
P. Diagonal car safety belt slot
Q. Belt threading slots
R. Slot elements for the child car seat har-
ness straps
S. Stabiliser block
(*) Shape and model can differ according
to the child car seat version being used.
(**) Optional

1.4 POSITIONS OF THE HANDLE

The child car seat carry handle can be ad-
justed to 4 positions (Diag. 5)
A. Position when travelling by car (WARNING:
this is the only position allowed when
travelling by car).
B. Position when carried by hand.
C. Rocker chair mode position or when
you need to fasten it to an appropriate
Chicco stroller.
D. Fixed rocker chair position.
To adjust the position, press both buttons
(M) on the handle bar together and rotate
it to the desired position until you hear it
click into place.
1.5 RESTRICTIONS AND REQUISITES
REGARDING THE USE OF THE PROD-
UCT AND CAR SEAT
WARNING! Read these restrictions and requi-
sites carefully to ensure the product and car
seat are used safely: if you don't, the safety
levels cannot be guaranteed.
• The child car seat can be fitted onto the
front passenger seat or any other back
seats. In any case the vehicle seat must
be facing forwards. Never use this child
car seat on vehicle seats which are facing
sideways or facing rearwards (diag. 6)
• The vehicle seat must be fitted with a
3-point static or 3-point retractor safety
belts approved to UN/ECE Regulation
No.16, or other equivalent standards
(Diag. 7).
• WARNING! In case of use in vehicles
equipped with rear seat belts with inte-
grated airbags (inflatable belts), the interac-
tion of the inflatable portion of the vehicle's
belt with this child restraint can result in
serious injury or death! Do not install this
child restraint using an inflatable seat belt.
• WARNING! Never fit the child car seat to a
vehicle seat that is only equipped with a
2-point safety belt (Diag. 8)
• Never use the booster cushion if the child
weighs more than 6 kg.
• Make sure that the buckle seat belt is not
too high (Diag 13-19). Otherwise, try to
install the car seat for your child on another
car seat in the car.

2. CAR INSTALLATION

The child car seat can be installed with or
without the base (optional). In both cases,
the child car seat must always be installed
facing rearwards.
2.1 INITIAL CONFIGURATION OF THE
HARNESS STRAPS AND SHOUL-
DER PADS
The child car seat is fitted with 2 different
types of shoulder straps (A and B) according
to the version being used. Before using the
child car seat, assemble the shoulder straps
as follows:
• Shoulder straps version A (Diag. 9A, 9B and
9C): thread the harness straps through the
slots in the fabric cover (not through the
seat structure below) so that they are vis-
ible on the seat. Thread the harness buckle
through the crotch pad.
• Shoulder straps version B (Diag. 10A and
10B): thread the harness straps though the
two shoulder pads. Thread the harness
buckle through the crotch pad.
2.2 INSTALLATION WITH THE BASE
To install the child car seat with base on the
vehicle seat, proceed as follows:
1. Remove the child car seat from the base
by pulling the release lever behind the
backrest whilst using the carry handle to
lift it upwards (Diag. 11).
2. Position the base on the chosen vehicle
seat, position it as seen in Diag. 12 so that
it touches the vehicle seat backrest.
3. Pull the vehicle safety belt and connect
it to the relative buckle, threading the
abdominal belt through the two slots (L)
16
i
a
4. B
t
i
5. A
(
d
p
6. C
fi
r
7. P
i
o
W
d
t
8. P
l
n
9. T
i
1
WA
Aft
ch
en
the
fit
tha
To
ba
1. U
s
f
2. B
t
3. R
a
2.3
To
pro
1. F
t
s
2. P
i
h