Recommended Fuels - EINHELL MT 24 Bedienungsanleitung

Anleitung MT 24-MTK 24 SPK 1
• Fuel Mixing Table
Gasoline Lubricant
5 Liters 125 ml (cc)
Mixing Procedure 40 Parts Gasoline to
1 part Lubricant
1 ml = 1 cc

RECOMMENDED FUELS

Some conventional gasolines are being blended with
oxygenates such as alcohol or an ether compound to
meet clean air standards. Your engine is designed to
operate satisfactorily on any gasoline intended for
automotive use including oxygenated gasolines.
OPERATING INSTRUCTIONS
• STARTING A COLD ENGINE
NOTE: To minimize load on engine during starting
and warm-up, trim excess cutter line to 5" (13cm)
(Fig. 5A).
1. Move ignition switch to the "RUN (I)" position (Fig.
5B).
2. Your unit is designed with a 3 position choke:
CHOKE " ", PARTIAL " ", and RUN " ". Move
choke lever to CHOKE " " position (Fig. 5C).
3. Prime the carburetor. Pump the primer bulb (A)
10 times (Fig. 5D).
4. Grip handle firmly – depress safety trigger (B) &
throttle trigger (C) to the FULL THROTTLE
position (Fig. 5E).
5. Pull starter rope out a short way until resistance
is felt (approximately 100mm) (Fig. 5F). A
smooth rapid pull is required for a strong spark.
Pull starter rope briskly 4 times.
6. Move choke lever to PARTIAL " " position (Fig.
5G).
7. Pull starter rope again 4 times while trigger is in
the full throttle position (Fig. 5F)
8. Once engine starts, leave in the PARTIAL " "
position for 10 seconds.
9. Move the choke to RUN " " position (Fig. 5H).
10. If engine fails to start, repeat steps 1 through 7.
NOTE: If engine fails to start after repeated attempts,
refer to Troubleshooting section.
09.11.2004 15:19 Uhr Seite 19
NOTE: Always pull starter rope straight out. Pulling
starter at an angle will cause rope to rub against the
eyelet. This friction will cause the rope to fray and
wear more quickly. Always hold starter handle when
rope retracts. Never allow rope to snap back from
extended position. This could cause rope to snag or
fray and also damage the starter assembly.
• WARM ENGINE START
1. Place trimmer on firm flat surface.
2. Move ignition switch to the "RUN (I)" position (Fig.
6).
3. Grip handle firmly, squeeze throttle trigger to
FULL position.
4. Pull starter rope briskly until engine starts, but no
more than 6 times.
5. If engine does not start, please operate
"STARTING A COLD ENGINE" again.
• TO STOP ENGINE
Release throttle trigger. Let engine return to idle.
Push and hold ignition stop switch until engine stops
(Fig. 6).
Trimming Instructions
• ADDITIONAL SAFETY PRECAUTIONS
Before operating your unit, review ALL SAFETY
PRECAUTIONS in this manual.
WARNING / CAUTION
• IF UNFAMILIAR WITH TRIMMING techniques,
practice the procedures with ENGINE in "OFF"
position.
• ALWAYS CLEAR WORK area of debris such as
cans, bottles, rocks, etc. Striking objects can cause
serious injury to operator or bystanders and also
damage equipment. If an object is accidentally hit,
immediately TURN ENGINE OFF and examine
equipment. Never operate unit with damaged or
defective equipment.
• ALWAYS TRIM OR CUT AT HIGH ENGINE
SPEEDS. Do not run engine slowly at start or
during trimming operations.
• DO NOT use equipment for purposes other than
trimming or mowing weeds.
• NEVER raise stringhead above knee height during
operation.
• DO NOT operate unit with other people or animals
in the immediate vicinity. Allow a minimum of 50
feet (15 meters) between operator and other
people and animals when trimming or mowing.
Allow a distance of 100 feet (30 meters) between
GB
19