Operation - Elica LIB0123112 Montage- Und Gebrauchsanweisung

Operation

The hood is fitted with a control panel with aspiration speed
selection control and a light switch to control cooking area
lights.
T1. Button ON/OFF lights (Led L1 lit)
T2. Button OFF – Selection button suction speed (power)
1 (Led L2 lit)
T3. Selection button suction speed (power) 2 (Led L2+L3
lit)
T4. Selection button suction speed (power) 3 (Led
L2+L3+L4 liti)
T5. Selection button intensive suction speed (power)
(Led L2+L3+L4 lit + Led L5 flashing) - duration 5 minutes
– after which the hood automatically sets suction speed
(power) 2.
Delayed switch-off of the hood (flashing LEDs):
It is possible to set the delayed hood switch-off by pressing
again for more than 2 seconds the button of the suction speed
(power) active at that time.
The available delayed switch-off options are:
Suction speed (power) 1: 20 minutes
Suction speed (power) 2: 15 minutes
Suction speed (power) 3: 10 minutes
Intensive suction speed (power): 5 minutes
Filter saturation indicator
The hood is equipped with a function that warns the user, at
regular time intervals, when the filters are saturated and it is
necessary to perform their maintenance.
Grease filter saturation indicator: With the hood off (OFF)
all suction speed (power) LEDs light up with steady light for 40
seconds.
Activated charcoal filter saturation indicator: With the
hood off (OFF) all suction speed (power) LEDsflash for 40
seconds.
Activation of the active charcoal filter saturation
signal: normally, this function is disabled; to activate it,
switch off the hood (OFF) and simultaneously press
buttons T3 and T5 for more than 3 seconds. LEDs L3
and L5 will start flashing.
To disable repeat the operation: LEDs L3 and L5 light up
with steady light.
Resetting the filters' saturation indicator:
With the hood on (ON) press button T2 for more than 2
seconds; all LEDs will light up briefly.
Note: if necessary, repeat the operation in case both
indicators (grease filter and activated charcoal filter) are
active.
Maintenance
Cleaning
Clean using ONLY the cloth dampened with neutral liquid
detergent. DO
INSTRUMENTS. Do not use abrasive products. DO NOT USE
ALCOHOL!
Grease filter
Fig. 16-18
Traps cooking grease particles.
The grease filter must be cleaned once a month using non
aggressive detergents, either by hand or in the dishwasher,
which must be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Charcoal filter (filter version only)
Fig. 17
It absorbs unpleasant odours caused by cooking.
The saturation of the charcoal filter occurs after more or less
prolonged use, depending on the type of cooking and the
regularity of cleaning of the grease filter.
In any case it is necessary to replace the cartridge at least
every four months.
The charcoal filter may NOT be washed or regenerated.
Circular carbon filter
Apply one on each side as cover to both the shield grids of the
motor impeller, then turn clockwise.
For the disassembly, turn counter-clockwise.
Replacing lamps
Fig. 19
Disconnect the appliance from the electricity.
Warning! Prior to touching the light bulbs ensure they are
cooled down.
Replace the old light bulb with the one of the same type as
specified in the feature label or near the light lamp on the
hood.
1. Using a flat head screwdriver or equivalent tool, carefully
pry loose the light cover.
2. Remove the damaged light and replace with a new 12
Volt, 20 Watt (Maximum) halogen light made for a G-4
base SUITABLE FOR USE IN OPEN LUMINAIRES.
Follow package directions and do not touch new light
with bare hands.
3. Reinstall the light cover. (it will snap shut).
If the lights do not work, make sure that the lamps are fitted
properly into their housings before you call for technical
assistance.
12
NOT CLEAN WITH TOOLS OR