Scheppach HC550TC-400V Original Bedienungsanleitung Seite 23

12 Secure the work piece
– Use clamps or a vice to hold the work piece
firmly. They will hold it more securely than your
hand can.
13 Avoid abnormal postures
– Make sure to stand securely and always keep
your balance.
14 Maintain your tools with care
– For better and safer work, keep cutting tools
sharp and clean.
– Follow the instructions for lubrication and
changing tools.
– Regularly inspect the electric tool's connection
cable, and if it is damaged, have it replaced by
an authorized expert.
– Regularly check extension cords, and replace
them if they are damaged.
– Keep the handles dry, clean and free of oil and
grease.
15 Pull the plug from the socket
– When not using the electric tool, before main-
tenance or when changing tools, such as saw
blades, drills and cutting bits.
16 Do not leave any tool keys inserted
– Before switching on, check to see that keys and
adjustment tools have been removed.
17 Avoid unintentional activation
– When plugging the tool in, make sure that the
switch is turned off.
18 Use outdoor extension cords
– When outdoors, use only extension cords that
are approved and appropriately marked.
– Only use cable reels in the unrolled state.
19 Be alert
– Pay attention to what you do. Approach your
work sensibly. Do not use the electric tool when
you are distracted.
20 Check the electric tool for damage
– Before using the electric tool, you must inspect
safety equipment or slightly damaged parts
carefully to ensure that they work properly and
as intended.
– Check to see that the moving parts operate
freely and don't stick, and to make sure no parts
are damaged. All parts must be mounted prop-
erly and meet all the conditions for ensuring
trouble-free operation of the electric tool.
– Damaged safety equipment and parts must be
properly repaired or replaced by a professional
facility, unless otherwise indicated in the user
manual.
– Damaged switches must be replaced by a cus-
tomer service facility.
– Never use an electric tool whose switch cannot
be turned on and off.
21 CAUTION!
– Using other insertion tools and accessories
may cause injury.
22 Have your tool repaired by an electrical expert
– This electric tool meets applicable safety re-
quirements. Repairs must be made only by an
electrical expert using original replacement
parts. Otherwise accidents many occur.
23 Noise
– Wear ear muffs when you use the compressor.
24 Replacing the power cable
– To prevent hazards, leave the replacement of
damaged power cables strictly to the manufac-
turer or a qualified electrician. There is a risk
of electric shock!
25 Inflating tires
– Directly after inflating tires, check the pressure
with a suitable pressure gauge, for example at
your filling station.
26 Roadworthy compressors for building site oper-
ations
– Make sure that all lines and fittings are suitable
for the maximum permissible operating pres-
sure of the compressor.
27 Place of installation
– Set up the compressor on an even surface.
28 Supply hoses at pressures above 7 bar should be
equipped with a safety cable (e.g. a wire rope).
ADDITIONAL SAFETY INSTRUCTIONS
Safety instructions for working with compressed
air and blasting guns
• The compressor pump and lines can become
very hot during operation. Touching these parts
will burn you.
• The air which is sucked in by the compressor must
be kept free of impurities that could cause fires or
explosions in the compressor pump.
• When releasing the hose coupling, hold the hose
coupling piece with your hand. This way, you can
protect yourself against injury from the rebound-
ing hose.
• Wear safety goggles when working with the blow-
out pistol. Foreign bodies or blown off parts can
easily cause injuries.
• Do not blow at people with the blow-out pistol and
do not clean clothes while being worn. Risk of in-
jury!
Safety information for paint spraying
• Do not process any paints or solvents with a flash
point below 55° C. There is a risk of explosion!
• Do not heat up paints or solvents. There is a risk
of explosion!
• If hazardous liquids are processed, wear protec-
tive filter units (face guards). Also, adhere to the
safety information provided by the manufacturers
of such liquids.
GB | 23