Specifications; Additional Safety Rules - Makita JN1601 Betriebsanleitung

ENGLISH
1 Die
2 Die holder
3 Lock nut
4 Wrench
5 Switch lever
6 Gauge for cutting stainless:
1.2 mm
7 Gauge for cutting mild steel:
1.6 mm
8 Notch

SPECIFICATIONS

Model
Max. cutting capacities
Steel up to 400 N/mm
Steel up to 600 N/mm
Steel up to 800 N/mm
Aluminum up to 200 N/mm
Min. cutting radius
Outside edge ..................................................... 50 mm
Inside edge ........................................................ 45 mm
Strokes per minute ................................................. 2,200
Overall length ..................................................... 261 mm
Net weight ............................................................. 1.6 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Always lead the power supply cord away from
the tool towards the rear.
2. Do not touch the blade or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
4
Explanation of general view
9 From the top view
10 Cutting at an angle to grooves
11 Cutting perpendicular to
grooves
12 From the side view
13 Corrugated or trapezoidal sheet
metal
14 Cutting head should be at a
right angle (90°) to cutting sur-
face
2
........................... 1.6 mm/16 ga
2
........................... 1.2 mm/18 ga
2
........................... 0.8 mm/22 ga
2
................... 2.5 mm/13 ga
OPERATING INSTRUCTIONS
JN1601
Charging the die position (Fig. 1)
Important:
Always be sure that the tool is switched off and
unplugged before changing the die position.
The die position can be changed 360°. To change it, pro-
ceed as follows.
1. Loosen the lock nut with the wrench provided.
2. Pull the die holder slightly and turn it to the desired
position for operation.
3. Tighten the lock nut to secure the die holder in the
desired position.
There are four positive stops at 90° each: 0°, 90° left and
right and 180°.
To position the die to any of these positive stops:
1. Loosen the lock nut with the wrench provided.
2. Pull the die holder slightly and depress lightly while
turning it to the desired position. The die holder will
lock into one of the positive stop positions as
desired.
3. Turn the die holder slightly to make sure that it is
positively locked into position.
4. Tighten the lock nut to secure the die holder.
Switching ON and OFF (Fig. 2)
Caution:
Before plugging in the tool, always check to see that the
switch actuates properly and returns to the "OFF" posi-
tion when the rear of the switch lever is depressed.
To switch on, depress the rear of the switch lever and
push it forward. Then depress the front of the switch lever
to lock it.
To switch off, depress the rear of the switch lever.
Thickness gauge (Fig. 3)
The groove in the die holder serve as the thickness
gauge for allowable cutting thickness.
Cutting line (Fig. 3)
The notch in the die holder indicates your cutting line. Its
width is equal to the cutting width. Align the notch to the
cutting line on the workpiece when cutting.
Pre-lubrication
Coat the cutting line with tool oil to increase the punch
and die service life. This is particularly important when
cutting aluminum.
15 Loosen
16 Tighten
17 Hex wrench
18 Bolts
19 Punch
20 Punch holder
21 Screw
22 Limit mark
23 Brush holder cap
24 Screwdriver