English - Hoonved CAP 10 E Gebrauchs - Und Wartungsanweisungen

Part 2: For the operator
2.1 CAP/SO E WASHING PHASES
2.1.a Machine OFF
When the machine is switched OFF the display will
read "OFF":
Display
IL SI
2.1.b Switching on and preparing the machine
To switch the machine on, press the "IL" button. The
LED representing the last cycle selected remains
CONSTANTLY LIT (LC1 - LC2 - LC3 -
LC1 LC2 LC3 LC4
ATTENTION
When switching on for the first time, the
light remains CONSTANTLY LIT.
First the boiler then the tank will begin to fill
automatically.
While the machine is filling up the display will read
"F2".
Once filled, the water-heating elements will be
activated, first in the boiler then in the tank.
The display will give the tank temperature;
IMPORTANT
It is advisable, when first switching on, to wait
until the display reads 55
WASHING OPERATION
If not equipped with an automatic dosing system,
pour into the tank a quantity of detergent suitable
for the volume and hardness of the water. For
quantities, refer to the specific instructions for the
detergent in use.
ATTENTION
When items to be washed are encrusted with
burnt-on matter, or a long time has passed
between use and washing, it is essential to
carry out a pre-wash soak using a suitable
softening agent.
The use of hand-washing products is to be
avoided as they could produce foam inside the
machine.
IPlace the basket of items to be washed inside the
machine, having first removed any solid waste.
CYCLE
START
LC1LC2LC3LC4
SD
ST
LC4).
LC2
°
C.
2.1.c Cycle selection
Press the "SD" or CYCLE button to select the washing cycle
required from the 4 different cycles available (SHORT,
MEDIUM, LONG, INTENSIVE) and specifically:
CAP 10E
LC 1: SHORT CYCLE
LC 2: MEDIUM CYCLE = 100 sec.
LC 3: LONG CYCLE
LC 4: INTENSIVE CYCLE = 8 min.
CAP 12E
LC 1: SHORT CYCLE
LC 2: MEDIUM CYCLE = 85 sec.
LC 3: LONG CYCLE
LC 4: INTENSIVE CYCLE = 8 min.
During the INTENSIVE cycle it is in any case possible to stop the
cycle before the end of the programmed time for LC4 by pressing
the START "ST" button again.
The minimum time for the INTENSIVE cycle will always
and in all cases be 120 sec.
2.1.d STARTING UP THE WASHING CYCLE
The selection of MANUAL orAUTOMATIC start to be made
with machine in stand-by mode.
The setting modality of cycle starting-up is the
AUTOMATIC.
2.1.d.1 STARTING UP THE WASHING CYCLE MANUALLY
To start up the cycle MANUALLY, press and hold the START
"ST" button for approx. 2 sec.
E
C L
C Y
S D
C 4
3 L
L C
C 2
1 L
L C
The LEDs of the display will light on in sequence and the
message shown on the display will blink (indicating that the
cycle is underway) at the LED for the selected cycle will
FLASH (e.g., LC2);
LED for pre-selected cycle
Display cycle underway LED
2.1.d.2STARTINGUPTHEWASHING CYCLEAUTOMATICALLY
To start up the cycle AUTOMATICALLY (by opening and
closing the door), you will need to change the cycle start-up
mode. Press and hold the START "ST" button until the pre-
selected cycle LED remains CONSTANTLY LIT (approx. 10
sec.) and the washing cycle will then start up
AUTOMATICALLY when the door is closed.
The functioning of the led (CONTINUOUS or BLINKING)
depends on the chosen type of functioning(MAN. or AUT)
2.1.e Instructions during the washing cycle
2.1.e.1 Display information
1) During washing, the tank temperature is indicated and the
display LEDs light up in sequence.
Display cycle underway LED
2) During drip-drying, only the display LEDs light up.

ENGLISH

= 65 sec.
= 150 sec.
= 55 sec.
= 120 sec.
IMPORTANT
T
A R
S T
S T
LC1 LC2 LC3 LC4
LC1 LC2 LC3 LC4
LC1 LC2 LC3 LC4
29