Operation; Maintenance; Ec Declaration Of Conformity - Makita TD020D Betriebsanleitung

OPERATION

The tool can be used in two ways; a straight type and a
pistol type which is selectable according to the conditions
of workplace and screwdriving. (Fig. 9 & 10)
CAUTION:
• When bending the tool to use in the pistol type or
straightening to use in the straight type, do not hold the
bendable part of the tool. Failure to do so may cause
your hand and fingers to be pinched and injured by this
part.
Hold the tool firmly and place the point of the driver bit in
the screw head. Apply forward pressure to the tool to the
extent that the bit will not slip off the screw and turn the
tool on to start operation.
The proper fastening torque may differ depending upon
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between fas-
tening torque and fastening time is shown in the figures.
(Fig. 11 & 12)
NOTE:
• Use the proper bit for the head of the screw/bolt that
you wish to use.
• Hold the tool pointed straight at the screw.
• If you tighten the screw for a time longer than shown in
the figures, the screw or the point of the driver bit may
be overstressed, stripped, damaged, etc. Before start-
ing your job, always perform a test operation to deter-
mine the proper fastening time for your screw.
The fastening torque is affected by a wide variety of fac-
tors including the following. After fastening, always check
the torque with a torque wrench.
1. When the battery cartridge is discharged almost
completely, voltage will drop and the fastening
torque will be reduced.
2. Driver bit or socket bit
Failure to use the correct size driver bit or socket bit
will cause a reduction in the fastening torque.
3. Bolt
• Even though the torque coefficient and the class of
bolt are the same, the proper fastening torque will
differ according to the diameter of bolt.
• Even though the diameters of bolts are the same,
the proper fastening torque will differ according to
the torque coefficient, the class of bolt and the bolt
length.
4. The manner of holding the tool or the material of
driving position to be fastened will affect the torque.
Using the tool as a hand screwdriver (Fig. 13)
Switch off the tool.
Move the lock button to the locked position
Turn the tool.
NOTE:
• Use the tool with a fastening torque less than 12.5 Nm.
• This use is convenient for checking the screwdriving.
• Do not use the tool for work requiring excessive force,
such as tightening bolt M10 or bolts greater than M10
or removing rusted screws.
8

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Phillips bit
• Socket bit
• Drill chuck attachment
• Soft carrying case
• Bit piece
• Various type of Makita genuine batteries and chargers
For European countries only
The typical A-weighted sound pressure level is 85 dB (A).
Uncertainty is 3 dB (A).
The noise level under working may exceed 85 dB (A).
The typical weighted root mean square acceleration
value is 4 m/s
These values have been obtained according to
EN60745.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
is in compliance with the following standards of standard-
ized documents,
in accordance with Council Directives, 89/336/EEC and
98/37/EC.
.
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes,
Bucks MK15 8JD, ENGLAND
Responsible manufacturer:
Makita Corporation Anjo Aichi Japan
Noise and Vibration
– Wear ear protection. –
2
.
EN60745, EN55014
CE 2006
Yasuhiko Kanzaki
Director
ENH102-5