English - Nilfisk-Advance SW650 S Bedienungsanleitung

ENGLISH

NILFISK SW 650S
INTRODUCTION
This manual will help you get the most from your Nilfisk-
Advance SW 650S. Read it thoroughly before operating the
machine.
This product is intended for commercial use only.
PARTS AND SERVICE
Repairs, when required, should be performed by your
Authorized Nilfisk-Advance Service Center, who employs
factory trained service personnel, andmaintains an inventory of
Nilfisk-Advance original replacement parts and accessories.
NAME PLATE
The Model Number and Serial Number of your machine are
shown on the Nameplate on the machine. This information is
needed when ordering repair parts for the machine. Use the
space below to note the Model Number and Serial Number of
your machine for future reference.
MODEL NUMBER___________________________________________
SERIAL NUMBER____________________________________________
UNCRATE THE MACHINE
When the machine is delivered, carefully inspect the shipping
carton and the machine for damage. If damage is evident, save
the shipping carton so that it can be inspected. Contact the
Nilfisk-Advance Customer Service Department immediately to
file a freight damage claim.
ASSEMBLY
ASSEMBLING HANDLE
1 Place ends of lower handle into holes of sweeper frame.
Attach with screws (see Figure 1).
2 Attach upper handle to lower handle using machine screws,
lockwashers, and nuts (see Figure 2).
3 Hopper handle should be attached to the dirt hopper with
screws provided (see Figure 3).
FIGURE 1
A= Lower Handle
B= Sweeper Frame
FIGURE 2
A= Upper Handle
B= Lower Handle
FIGURE 3
A= Hopper Handle
B= Sweeper Hopper
ASSEMBLING SIDE BROOM
1 Drive belt should be positioned on the pulley when received.
Check to ensure belt is on the pulley, and between belt guides.
2 With the side arm positioned as shown in Figure 4, place
the belt between the walls of the side broom arm. Place
the outside tracking belt over the rear wheel and above the
mounting bracket. The inside tracking belt must be UNDER the
mounting bracket.
3 Attach the side broom arm to the mounting bracket, by
aligning the holes in the arm with the holes in the mounting
bracket. Insert clevis pins and secure with hairpin clips.
4 Place side broom bumper on the side broom pulley with the
outside flange toward side broom. Attach side broom to the
side broom pulley with screws, lockwasher and washers.
5 Lower side broom arm and replace hopper.
6 If side broom rotates in the wrong direction, the belt is not
installed correctly.
20
FIGURE 4
A= Broom Pulley
B= Broom Arm
C= Outside Tracking
D= Hairpin Clip
E= Clevis Pin
F= Side Broom
G= Broom Bumper
H= Inside Tracking
I= Belt Guides
J= Mounting Bracket
SIDE BROOM
Refer to Figure 5.
1 The side broom should be lowered and used when sweeping
along curbs or walls; it may also be used when sweeping open
areas.
2 Side broom height should be adjusted to have approximately
1/3 of the bristles touching the floor. Adjustment can be made
by turning the adjustment knob.
FIGURE 5
A= Side Broom Arm
B= Side Broom Arm
C= Sweeper
OPERATING PUSH SWEEPER
Push sweeper forward at normal walking speed; it does not
operate when pulled backwards.
EMPTYING DIRT HOPPER
1 To empty the dirt hopper, lift up on the handle located on
the front of the hopper, and empty contents into a proper
container.
2 Replace dirt hopper back on sweeper by placing front edge
of hopper on sweeper frame.
3 Apply downward pressure until the hopper is in its proper
position.
4 The dirt hopper should be emptied after each use, or as
required. A full dirt hopper will affect the sweeping efficiency
of the push sweeper.
FIGURE 6
A= Dirt Hopper
B= Sweeper Frame
MAINTENANCE
1 After each use, check for materials which may have become
wrapped around brushes or wheels, and remove immediately.
2 Do not lubricate gears, clutch or other internal parts.
3 Inspect rubber dust seals periodically for wear or damage;
replace as required.
4 Side broom should be inspected periodically for wear;
replace when (with the adjustment in the down position) less
than 1/3 of the bristles come in contact with the surface. The
side broom can be easily replaced by removing the screws
from the brush holder and reassembling the replacement
brush, using the same hardware.