Additional Safety Rules - Makita 9207SPB Betriebsanleitung

Wear protecting hair covering to contain long hair.
9. Use safety glasses and hearing protection.
Also use face or dust mask if the cutting operation is
dusty.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust
extraction and collection facilities ensure these are
connected and properly used.
11. Do not abuse the cord.
Never carry the tool by the cord or yank it to discon-
nect it from the socket. Keep the cord away from
heat, oil and sharp edges.
12. Secure work.
Use clamps or a vice to hold the work. It is safer than
using your hand and it frees both hands to operate the
tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep cutting tools sharp and clean for better and safer
performance. Follow instructions for lubrication and
changing accessories. Inspect tool cord periodically
and if damaged have it repaired by an authorized ser-
vice facility. Inspect extension cords periodically and
replace, if damaged. Keep handles dry, clean and free
from oil and grease.
15. Disconnect tools.
When not in use, before servicing and when changing
accessories such as blades, bits and cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning it on.
17. Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on the
switch. Ensure switch is off when plugging in.
18. Use outdoor extension leads.
When tool is used outdoors, use only extension cords
intended for outdoor use.
19. Stay alert.
Watch what you are doing. Use common sense. Do
not operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to deter-
mine that it will operate properly and perform its
intended function. Check for alignment of moving
parts, free running of moving parts, breakage of parts,
mounting and any other conditions that may affect its
operation. A guard or other part that is damaged
should be properly repaired or replaced by an autho-
rized service center unless otherwise indicated in this
instruction manual. Have defective switches replaced
by an authorized service facility. Do not use the tool if
the switch does not turn it on and off.
21. Warning.
The use of any accessory or attachment, other than
those recommended in this instruction manual or the
catalog, may present a risk of personal injury.
22. Have your tool repaired by a qualified person.
This electric tool is in accordance with the relevant
safety requirements. Repairs should only be carried
out by qualified persons using original spare parts,
otherwise this may result in considerable danger to
the user.

ADDITIONAL SAFETY RULES

1. Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves,
helmet and apron should be worn.
2. Always be sure that the tool is switched off and
unplugged before carrying out any work on the
tool.
3. Accessories must be rated for at least the speed
recommended on the tool warning label. Wheels
and other accessories running over rated speed can
fly apart and cause injury. Maximum operating speed
of accessories should be higher than the highest no
load speed marked on the tool's name-plate.
4. Check the backing pad carefully for cracks, dam-
age or deformity before operation. Replace
cracked, damaged or deformed pad immediately.
5. Check that the workpiece is properly supported.
6. Hold the tool firmly.
7. Keep hands away from rotating parts.
8. Make sure the abrasive disc or wool bonnet is not
contacting the workpiece before the switch is
turned on.
9. When sanding metal surfaces, watch out for flying
sparks. Hold the tool so that sparks fly away from
you and other persons or flammable materials.
10. Do not leave the tool running. Operate the tool
only when hand-held.
11. Pay attention that the wheel continues to rotate
after the tool is switched off.
12. Do not touch the workpiece immediately after
operation; it may be extremely hot and could burn
your skin.
13. If working place is extremely hot and humid, or
badly polluted by conductive dust, use a short-cir-
cuit breaker (30 mA) to assure operator safety.
14. Do not use the tool on any materials containing
asbestos.
15. Do not use water or grinding lubricant.
16. Ventilate your work area adequately when you per-
form sanding operations.
17. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
18. Always use the correct dust mask/respirator for
the material and application you are working with
when sanding.
19. Ensure that ventilation openings are kept clear
when working in dusty conditions. If it should
become necessary to clear dust, first disconnect
the tool from the mains supply (use non metallic
objects) and avoid damaging internal parts.
5