Camargue ÄLVSBORG Installationsanleitung Seite 16

Important before installation
1. Only a certified electrician / plumber can install the whirlpool and only a certified plumber can install the tub.
2. The heating element is designed for keeping the water in the tub at 38-40°C. It is not designed for warming up the cold water to a bathing
temperature.
3. Bathtub is to be installed with at least 50cm distance from the nearest object so that possible service can be done. If the bathtub is not installed
within the recommended range can the manufacturer refuse to do the reparations within warranty period. Do not place immovable object in that
space.
4. If the bathtub is sealed with silicon remove the silicon before possible reparation. The service man does not restore any silicon sealings.
5. Prevent the tub from damage during the installation. Be careful so that the tub does not get scratched by sharp tools like a screwdriver and other
tools. Be careful when you move the tub so that the feet does not damage the floor.
6. Use the adjustable feet to install the tub horizontally. Drawing (4c).
7. Take of the front panel. Drawing (2).
8. Remove the protection foil on the blower and connect the pipe. Drawing (3g).
Electrical requirements
9. Electrical installations shall be made according to relevant applicable rules. All electrical installations must be water resistant and all electrical
installation should include a waterproof switch.
10. Your electrical installation should be powerful enough to run all the connected electrical components at the same time. Drawing (7).
11. Additionally, install the earth wire and make sure that the earth wire works properly. Do not let the socket and contacts come in contact with
water.
Water installation
12. We recommend installing shut off valves on water pipes so that you can turn off the water to the tub. Drawing (8).
13. To the pre-installed parts of the tub you only need to connect the external cold and hot water hoses to the corresponding water pipes or
fittings. The connections shall be separated from the bathtub. Drawing (8).
14. Install the cone clutch on the shower hose to the shower head and put the other end of the shower hose through the hole where the shower
head is to be placed. Then attach the shower hose to the diverter.
15. Connect the flexible drain pipe to the water trap and then to the drain. Drawing (4, point a, b, c).
After installation
16. The distance between bathtubs edge and the wall is to be 0,5 cm. Use bathroom silicone to fill the gap and to seal the bathtub.
17. Finally, install the front panel as shown on the drawing. Place the front panel in place between the tub edge and attach the plastic disc.
Tighten the screws and put on the caps. Drawing (2).
Use the product
18. Turn on the power at the main switch.
19. Open the cold and hot water taps. Select the desired temperature and use the diverter to select between the faucet, hand shower and clean
function.
20. The pump can not be started before the water level reaches all the jets in the bathtub. The water level sensor will keep the pump off untill the
water reaches the sensor. Drawing (3f).
21. Start and stop the pump for water massage. Drawing (3b).
22. The intensity of the massage can be regulated by opening and closing the air supply by turning the air control knob clockwise or
counterclockwise. Drawing (3e).
23. Start and stop the pump for air massage. Drawing (3a).
24. Switch the underwater light with chromotherapy on/off. Drawing (3c).
25. Turn the overflow handle to empty the tub after use.
26. Turn off the power at the main switch after use.
Care taking
1. If you do not use the hot tub regularly, it is a good idea to clean out the old water in the pipes before using the tub again. You can clear away old
water from the pipes by opening the hot water tap and turn the diverter in the position "Clean". Drawing (6). Leave the waste open and let the
water run through the jets for a couple of minutes to flush out contingent dirty water into the pump and piping system.
2. When cleaning the massage unit fill the tub with water at a temperature of approx. 40 ° C and add 2 g detergent per 1 litre of water. Start the
massage function and let it run for approx. 5 minutes. Turn off the pump and drain the water out of the tub. Fill the tub again, this time with cold
water, and let the massage function for approx. 3 minutes. Turn off the pump and drain the water out of the tub. Finally, clean bathtub.
3. Use mild detergent and a soft cloth for the daily cleaning of the bubble bath. Detergents containing acetone or ammonia should not be used.
Also do not use abrasive cleaning agents or disinfectants containing formic acid or formaldehyde to disinfect the tub.
4. Do not use sharp tools or cleaners containing solvents or abrasives to clean the tub.
5. Scratches on the surface of the tub can be wet sanded. Use only 2000 sandpaper. Then lubricate the scratch with toothpaste and polish with a
soft cloth. Use car wax to polish bubble bath.
6. To get rid of limestone use a cloth soaked in warm lemon juice or vinegar.
7. Massage jets and drain filter can be removed and cleaned if they are blocked with hair etc.
8. Avoid scratching the tub with sharp objects. Lit cigarettes or other objects with temperature above 70 ° C must not come in contact with the
tub surface.
9. D o not use harsh cleaners or scouring pads on the chrome parts of the tub. You can scratch and remove the chrome surface.