Installation; Preparing The Shower Rod; Installing The Thermostatic Mixer; Installing The Shower Rod - Miomare DX1900CS-LIDL Montageanleitung

Installation

•
Installation
Note: Familiarise yourself with the shower set
before installation by carefully reading these
installation and operating instructions, particularly
the safety instructions.
If incorrectly installed, the warranty will become
invalid – particularly with regard to consequential
damages.
■ CAUTION! Turn off the hot and cold water
supply before starting the installation.
Note: To carry out the installation, you will
need the following tools (not included):
Drill and 6 mm drill bit,
Size 30 spanner,
Phillips-head screwdriver.
Note: Find out information on appropriate
mounting materials for your wall before installa-
tion. The enclosed mounting materials (screws
and wall plugs) are suitable for ordinary solid
masonry.
•

Preparing the shower rod

□
Make sure that the sealing ring with filter
properly inserted in the threaded connector for
the overhead shower head
□
Screw the overhead shower head onto the
upper connector on the shower rod
□
If necessary, loosen the clamping mechanism
by turning it anticlockwise a few times and adjust
the handheld shower head bracket
positioned on the side of the shower rod where
the handheld shower head should sit later on.
□
Screw the wall mount peg
mounting plate peg
□
Loosen the hex socket grub screw in the wall
mount peg by using the hex key
anti-clockwise a few times.
□
Insert the shower rod bracket holding pin
into the corresponding opening in the wall
mount peg.
□
To attach the shower rod to the wall mount peg,
tighten the hex socket grub screw by turning it
clockwise with the hex key.
16 GB/IE
26
and lying flat.
25
.
24
until it is
23
loosely onto the
3
, leaving the cover
5 4
to turn it
17
2
•

Installing the thermostatic mixer

□
Wrap the smaller threads (1/2 thread) on each
of the S connectors
(not included).
□
Screw the two S connectors to your wall con-
nectors until hand-tight. Please note that both
S connectors must sit at right angles to the wall
and must be screwed in by an equal amount.
□
Adjust the S connectors until the distance
between them is the same as that between the
connection points on the thermostatic mixer
(see Fig. A).
□
Screw a collar
each fitted S connector until hand-tight and
flush with the wall.
□
Make sure that the silencers
inserted in the S connectors. The side with the
smaller diameter must point towards the wall,
and the side with the larger diameter must point
towards the thermostatic mixer.
□
Place the thermostatic mixer onto the fitted S
connectors so that the temperature control
is on the right of the thermostatic mixer and the
is
flow control
□
Secure the thermostatic mixer by screwing both
union nuts
12
connectors until hand-tight. Please note that the
union nuts must be easy to unscrew and not
skewed in order to prevent the thermostat from
22
leaking.
□
Tighten the union nuts using a smooth size 30
spanner. To prevent damage, never use toothed
pliers.
•

Installing the shower rod

off.
□
Insert a sealing ring
union nut
21
□
Place the shower rod
ing) shower rod connector
union nut onto the thread until hand-tight.
□
Using the holes in the mounting plate
the position of the drill holes on the wall.
□
Loosen the union nut again and remove from
shower rod from the thermostatic mixer
□
Drill holes at the marked positions.
with a little sealing tape
9
onto the (thicker) thread of
11
are correctly
10
is on the left.
20
onto the threads of the two S
into the shower rod
7
.
onto the (upwards-fac-
24
and screw the
18
19
15
, mark
5
.
19