Christopeit Sport RS 100 Montage- Und Bedienungsanleitung Seite 16

Computer instructions for 1903
The supplied computer allows the most convenient training. Every value
relevant to training is displayed in a corresponding window.
From the beginning of the training session, the required time, the current
speed, the approximate calorie consumption, the travelled distance ad the
current pulse rate are displayed. All values are counted from zero upwards.
The computer is switched on by briefly pressing the F- key or simply by
beginning training. The computer begins to register and display all values.
To stop the computer, just stop training. The computer stops all
measurements and retains the last attained values. The last attained values
in the functions TIME, CALORIES and KM are stored for 4 Min. and training
can continue with these values when training is resumed.
The computer switches of automatically approx. 4 minutes after training
is stopped.
Displays:
1. „KM/H" Speed-display:
The current speed is displayed in kilometres per hour. It is not possible to
specify a particular value using the „E" key. The values last attained by this
function are not stored. (Limit of the display: 99.9 km/h.)
2. „ZEIT" Time-display:
The currently required time is displayed in minutes and seconds. It is
possible to specify a particular value using the „E" key. If a particular time
has been specified, the remaining time is displayed. When the specified
value is attained, this is indicated by an acoustic signal. The values last
attained by this function are stored. (Limit of the display: 99.59 minutes.)
3. „KM" Distance-display:
The current status of the travelled distance is displayed. It is possible to
specify a particular value using the „E" key. If a particular distance has
been specified, the remaining distance is displayed. When the specified
value is attained, this is indicated by an acoustic signal. The values last
attained by this function are stored. (Limit of the display: 999 km.)
4. „CALORIEN" Calory-display:
The current status of the consumed calories is displayed. It is possible to
specify a particular value using the „E" key. If a particular consumption
has been specified, the remaining number of calories to be consumed is
displayed. When the specified value is attained, this is indicated by an
acoustic signal. The values last attained by this function are stored. (Limit
of the display: 999 calories.)
5. „ODO" Km Total-display:
The current status of the travelled kilometres of all previous training
sessions including current training session is displayed. A particular value
cannot be speci. ed. The values last attained by this function are not
stored. (Limit of the display: 9.999 km.)
6. „SCAN" function:
If this function is selected, the current values of all functions are displayed
successively in a constant sequence approx. every 5 seconds.
Keys:
1. „F" key:
Pressing this key once briefly makes it possible to change from one
function to another, i.e. the respective functions can be selected for which
entries can be made using the „E" key. The currently selected function is
indicated by an icon in the respective window.
2. „E" key:
By pressing this key once, it is possible to specify values step by step
in the respective functions. For this, the desired function must firstly be
selected using the „F" key.
Holding the key pressed activates faster running, which can be stopped
by pressing the key again. When training begins, the specified values are
then counted down to zero.
3. „L" = Delete:
When this key is pressed briefly, the values chosen with the „F" key are
reset to zero. If the key is held longer (approx. 3 seconds), all last attained
values are deleted with the exception of the values in the „KM TOTAL"
display.
Replacing the batteries:
1. Open the battery compartment cover and then remove the used
Batteries. (If the batteries should leak remove them under increased
considering that the battery acid is not into contact with skin come and
clean the battery compartment thoroughly.)
2. Insert the new batteries (type (AAA) 1.5 V in the correct order and taking
into account the polarity in the battery compartment and close the battery
cover so that it clicks into place.
3. If the computer does not pick up immediately, the function should
Batteries are removed for 10 seconds and re-inserted.
4. The empty batteries properly in accordance with the disposal regulations
disposed of and do not give residual waste.
Battery compartment
AAA batteries
16