Safety Instructions; Initial Setup - swissflex uni 22_95RF bridge Bedienungsanleitung

Health and comfort
Welcome to the world of Swissflex!
Your Swissflex uni 20_/22_95RF bridge
quality product. If you follow the simple operating
and safety instructions, it will function to your com-
plete satisfaction for many years. In addition to
its many other advantages, your uni 20_/22_95RF
bridge offers an undisturbed sleep environment.
®
All electrical connections between the mains plug
and the bed are virtually free of mains voltage
(below 0.5 watts) thanks to EcoTec.

Safety instructions

CAUTION! The uni 20_/22_95RF bridge
sories must be protected from rain and other moistu-
re to prevent causing a fire hazard or the risk of elec-
tric shock. In case of spillages on an accessory, the
mains cable must be disconnected from the power
outlet and checked by your Swissflex stockist.
When installing the slat base, ensure that the head,
back and foot sections are not obstructed by furniture.
Ensure that the mains supply is disconnected befo-
re any assembly or disassembly work is carried out
on the slat base or the bed frame.
Do not connect any devices to the user socket (33)
that could endanger persons or damage objects
when the socket is turned on by remote control, in
particular electrical tools such as saws, drills and
similar (risk of injury) or portable heating devices
(risk of fire).
Never place the mains cable between the user socket
(33) and the bed in such a way that the cable insulati-
on could be damaged by sharp edges or twists. Never
feed the cable through the adjustment mechanism.
In the case of damage to cables to the control
housing or to the user socket (33), do not adjust the
bed to a seated position. Remove the mains plug
from the socket and inform your stockist.
Never open the user socket housing (33) to which
the cables are connected. If you interfere with any
electrical part of the user socket (33), the guaran-
tee entitlements will no longer apply.
Handle the uni 20_/22_95RF bridge
ries with care; do not disassemble or modify them,
do not allow children to play with them and prevent
frail individuals from using the product without su-
pervision.
The product may not be used with a medical device
or be installed in a medical device.
The product may not be used in an environment in
which flammable or explosive gases or vapours (e.g.
anaesthetics) are likely to occur.
The product may not be used to raise and lower
loads.
Only use spare parts that have been produced or
approved by Swissflex. Only these parts guarantee
adequate safety.
GB
is a Swiss
®

Initial setup

Place the batteries into the radio remote control
Remove the cover from the battery compartment
(21) on the back of the radio remote control. Place 3
AAA-batteries (22) into the compartment, paying at-
tention to the +/- markings. Close the compartment
cover again. The maximum range of the radio remote
control is 15 metres.
and acces-
®
Teaching-in the remote control (already taught-in in
the factory)
Remove the remote control's battery cover on the
back of the device.
1. Insert / check the batteries (3x AAA).
2. Activate the teach-in button on the switching power
supply (press 2x). It flashes after successful activa-
tion.
3. A small red button is located above the batteries in
the battery compartment.
4. Press the button; a blue LED will start flashing.
Hold the button down until the blue LED is per-
manently illuminated; this means that pairing has
been completed.
Bluetooth®
1. Download the standard „Swissflex" app from the
relevant platform for Android (Google play) or App-
le iOs (App Store).
2. Install the standard „Swissflex" app onto your
Smartphone / Tablet PC.
3. Check that the motor has a power supply and that
the Bluetooth® adapter is connected to the motor.
4. The Bluetooth® connection LED flashes for about
2 min.
5. Connect your Smartphone / Tablet PC via Blu-
etooth® using the control system, also see the
and accesso-
® Smartphone / Tablet PC instruction manual.
6. Enter the PIN (see type plate) if requested, other-
wise the Smartphone / Tablet PC connects auto-
matically.
7. Test the Bluetooth® connection and operation with
the Smartphone / Tablet PC.
8. The Bluetooth® connection LED turns blue as
soon as the Smartphone / Tablet PC is connected
to the control system (Bluetooth® is activated).
Synchro function (with sync cable)
When two uni 20_/22_95RF bridge
gether with a sync cable (connection jack 19), the
synchro function (17) is required. By pressing and
are linked to-
®
Operating instructions
13