Important Safeguards - Digital Projection HL12000Dsx+ Bedienungsanleitung

Important Safeguards

These safety instructions are to ensure the long life of your pro-
jector and to prevent fire and shock. Please read them carefully
and heed all warnings.
Installation
1. Place the projector on a flat, level surface in a dry area away from dust
and moisture. Tilting the front of the projector up or down from level
could reduce lamp life. Do not put the projector on its side when the
lamp is on.
Doing so may cause damage to the projector.
2. Do not place the projector in direct sunlight, near heaters or heat radi-
ating appliances.
3. Exposure to direct sunlight, smoke or steam could harm internal com-
ponents.
4. Handle your projector carefully. Dropping or jarring your projector could
damage internal components.
5. Do not place heavy objects on top of the projector.
6. If you wish to have the projector installed on the ceiling:
a Do not attempt to install the projector yourself.
b The projector must be installed by qualified technicians in order to
ensure proper operation and reduce the risk of bodily injury.
c In addition, the ceiling must be strong enough to support the projec-
tor and the installation must be in accordance with any local build-
ing codes.
d Please consult your dealer for more information.
e Do not attempt to stack projectors on the ceiling.
To Dealer or Installer:
To prevent the projector from falling, install it in a place and fas-
ten it in a way with sufficient strength to support the combined
weight (94 kg/ 207.3 lb) of the projector (84 kg/185.3 lb) and the
lens (10 kg/22 lb) for an extended period of time as well as to
withstand earthquakes.
Power Supply
1. The projector is designed to operate on a power supply of 2.8kW
(HL12000Dsx+/HL8000Dsx+)/ 3.0kW (HL12000HD/10000HD) AC200-
240V 50/60Hz. Ensure that your power supply fits this requirement be-
fore attempting to use your projector.
2. Handle the power cable carefully and avoid excessive bending. A dam-
aged cord can cause electric shock or fire.
3. If the projector will not be used for an extended period of time, dis-
connect the plug from the power outlet.
4. Do not touch the power plug with wet hand. Doing so can cause electri-
cal shock or fire.
5. Do not touch the power plug during a thunder storm. Doing so can
cause electrical shock or fire.
Cleaning
1. Unplug the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a
mild detergent. Never use strong detergents or solvents such as alco-
hol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to
scratch or mar the lens.
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unobstructed
to prevent potentially dangerous concentrations of ozone and the build-
up of heat inside your projector. Allow at least 8 inches (20cm) of space
between your projector and a wall. Allow at least 20 inches (50 cm) of
space between the ventilation outlet and object.
2. Prevent foreign objects such as paper clips and bits of paper from fall-
ing into your projector. Do not attempt to retrieve any objects that might
fall into your projector. Do not insert any metal objects such as a wire or
screwdriver into your projector. If something should fall into your pro-
jector, disconnect it immediately and have the object removed by a
qualified your service person.
3. Do not place any liquids on top of your projector.
4. When using a LAN cable:
For safety, do not connect to the connector for peripheral device wiring
that might have excessive Voltage.
5. Remote Control Precautions
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
if you will not be using the remote control for a long time, remove the
batteries.
Do not use new and old batteries together, or use different types of
batteries together.
Dispose of used batteries according to your local regulations.
CAUTION: High Pressure Lamp May Explode if Improperly
Handled. Refer Servicing to Qualified Service Personnel.
Lamp Caution: Please read before operation
Due to the lamp being sealed in a pressurized environment,
there is a small risk of explosion, if not operated correctly.
There is minimal risk involved, if the unit is in proper working
order, but if damaged or operated beyond the recommended
1000 hours, the risk of explosion increases.
Please note that there is a warning system built in, that dis-
plays the following message when you reach 1000 hours of
operation "The lamp has reached the end of its usable
life. Please replace the lamp" When you see this message
please contact your Dealer for a replacement.
If the lamp does explode, smoke will be discharged from the
vents located on the side of the unit. This smoke is comprised
of glass in particulate form and Xenon gas, and will not cause
harm if kept out of your eyes. If your eyes have been ex-
posed to this gas, please flush your eyes out with water im-
mediately and seek immediate medical attention. Do not rub
your eyes! This could cause serious injury.
WARNING:
• Do not look into the lens while the projector is on. Serious
damage to your eyes could result.
• When main body is damaged, cooling fluids may come out
of internal part.
Please do not touch and drink the cooling fluid.
When the cooling fluids are swallowed or contacted with
your eyes, please consult with doctors immediately.
CAUTION
Do not unplug the power cable from the wall outlet under any
one of the following circumstances. Doing so can cause dam-
age to the projector:
• While the message "Please wait a moment" appears. This
message will be displayed after the projector is turned off.
• Immediately after the power cable is plugged into the wall
outlet (the POWER indicator has not changed to a steady
orange glow).
• Immediately after the cooling fan stops working (After the
projector is turned off with the POWER OFF button the cool-
ing fan continues to work for 3 minutes while the Two Digit
INDICATOR "—" flashes).
5
Important Information