Scope Of Use; Safety Instructions And Symbols Used - EINHELL HSP 6/104 Bedienungsanleitung

Anleitung HSP_6-104_SPK1:Anleitung HSP41-1_HSP51_SPK1
Packaging
The device is supplied in packaging to prevent its
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
When using the equipment, a few safety
precautions must be observed to avoid injuries
and damage.
Read the operating instructions carefully and
comply with them. It is important to consult these
instructions in order to acquaint yourself with the
unit, its proper use and safety regulations.
Keep this manual in a safe place, so that the
information is available at all times.
If you give the equipment to any other person,
hand over these operating instructions as well.
We cannot accept any liability for damage or
accidents which arise due to a failure to follow
these instructions.

1. Scope of use

The wood splitter is designed for splitting wood with
maximum lengths of 520/770/1040 mm and a
maximum diameter of 320 mm. Please note that our
equipment has not been designed for use in
commercial, trade or industrial applications. Our
warranty will be voided if the equipment is used in
commercial, trade or industrial businesses or for
equivalent purposes.
2. Safety instructions and symbols
used
The applicable safety instructions and explanations
of the symbols on the device are set out in the
enclosed booklet.
3. Layout and items supplied (Fig. 1-2)
1. Splitter
2. Trunk support
3. Hand guards
4. Control lever
5. Trunk support holder
6. Supporting foot
7. Wheels
8. Switch/plug combination
9. Motor
10. Transport handle
11. Trunk holding plates
12. Chain for adjusting the splitter height
13. Screws for switch/plug combination
14. Axle
15. Washers for axle
16. Securing split pins for axle
17. Securing screws for control lever and hand
guards
18. Securing screws for trunk holding plates
19. Chain hook
20. 1 canister of hydraulic oil
21. Funnel
22. Motor circuit breaker switch
4. Assembly
4.1 Fitting the switch/plug combination (Fig. 3)
Install the switch/plug combination on the wood
splitter as shown in Figure 3. Use the four screws
(Fig. 2 / Item 13) for this purpose.
4.2 Fitting the transport handle (Fig. 4/5)
Remove the two screws in the transport handle using
an Allen key (Fig. 4). Place the transport handle over
the two holes in the cover on the rear cover of the
wood splitter and secure it with the two screws as
shown in Figure 5.
4.3 Fitting the wheels (Fig. 6-10)
Push a split pin (Fig. 2 / Item 16) through one of the
holes in the axle (Fig. 2 / Item 14) and bend it as
shown in Figure 6. Now slide a washer (Fig. 2 / Item
15) and a wheel (Fig. 2 / Item 7) over it (Fig. 7).
Guide the axle through the holes provided for it at the
bottom on the rear of the wood splitter (Fig. 8). Now
place the remaining wheel and washer on the axle
(Fig. 9) and secure it with the other split pin (Fig. 10).
4.4 Fitting the control lever and hand guards (Fig.
11-14)
Guide the hand guards and control level, as shown in
Figure 11, from the front into the wood splitter so that
the ends of the control lever project through the
recesses provided for it in the control rods (Fig. 12).
Then secure the hand guards using the appropriate
screws A and nuts B (Fig. 2 / Item 17) as shown in
Figures 13 – 14.
4.5 Fitting the trunk holding plates (Fig. 15-18)
Push the trunk holding plates (Fig. 2 / Item 11)
through the guide slots in the hand guards, as shown
in Figure 15. As you do this, ensure that the oval
holes in the trunk holding plates line up with the
securing holes in the hand guards. Remove the
15.12.2006 9:28 Uhr Seite 17
GB
17