Correct Use - IKA EUROSTAR series Kurzanleitung

• Use:
For mixing/stirring liquids with low and high viscosities by various
stirring tools.
Intended use: Stand device (chuck points down).
• Range of use (indoor use only):
- Laboratories - Schools
- Pharmacies - Universities
• Wireless remote control:
Before using the wireless link between the Wireless Controller
(WiCo) and the laboratory device, first check whether your re-
gion is included in the radio communications approval for the
device. If it is not, remote control can also be performed using
a USB cable.
Assemble the overhead stirrer and all necessary accessories on
a stable, even, non-slip surface. The EUROSTAR overhead stir-
rer must be secured to a stable stand (e.g. R 2722 or R 2723)
with a cross-sleeve (e.g. R 270). The stirring vessel must always
be securely fixed for safety reasons. You must also ensure that the
mounting device (stand) is set up in such a way that it is not liable
to topple and does not start to move during the stirring procedure.
Accessories must be assembled according to the assembly instruc-
tions (Fig. 2 to Fig. 8).
Check whether the voltage given on the type plate corresponds to
the available mains voltage.
The socket used must be earthed (fitted
with earth contact).
If these conditions have been met, the machine is ready for opera-
tion when the mains plug is plugged in.
If these conditions are not met, safe operation is not guaranteed
and the machine could be damaged.
Before the first time to use the EUROSTAR stirrer, fasten the Wireless
Controller (WiCo) to the station with the screw (P, see Fig. 1), so
that the rechargeable battery (RB1 battery pack) in the Wireless
Controller can be charged.
After the device has been switched on at the main switch (A, see
Fig. 1) the device name and software version appear in the display
(C, see Fig. 1) of the Wireless Controller (D, see Fig. 1).
E U R O S T A R
control
Version 1.1

Correct use

This instrument is suitable for use in all areas except:
- Residential areas
- Areas that are connected directly to a low-voltage supply net-
work that also supplies residential areas.
The safety of the user cannot be guaranteed:
- If the instrument is operated with accessories that are not sup-
plied or recommended by the manufacturer
- If the instrument is operated improperly or contrary to the manufac-
ture's specifications
- if the instrument or the printed circuit board are modified by third
parties.
Commissioning
After This the following working screen appears automatically in
the display.
B
0
Ncm
Torque:
Reset Torque 
Back
00:00:00
Timer:
0
actual rpm
0
set rpm
Rotate the rotary/push knob (B, see Fig. 1) to set the target speed.
Press the rotary/push knob (B), the stirrer starts to run with the set
speed.
If the Wireless Controller is switched on and is not attached to the stir-
rer (the station), the green LED bar (G, see Fig. 1) and the green Blue-
tooth LED (F, see Fig. 1) on the stirrer (station) will light up. Make
®
sure that the speed selected is appropriate for the trial run. If in doubt,
use the rotary knob (B, see Fig. 1) to select the slowest speed. To start
or stop the stirrer function, press the rotary knob (B, see Fig. 1).
The controls of the Wireless Controller can be disabled by pressing
the button (L) , so that no inadvertent changes are made while
the device is running (the key symbol
Pressing the button (L)
again (key symbol
WARNING
button (I, see Fig.1) on the front of the stirrer. In this case the LED
bar (G, see Fig.1) changes color from green to red, and flashes.
A message appears in the display, advising that the EUROSTAR stirrer
(station) has been forcibly switched off. To restart the stirrer, switch
the main switch (A, see Fig. 1) of the EUROSTAR stirrer (station)
OFF and ON.
If the Bluetooth ® function of the Wireless Controller is active, the
user can use the Bluetooth
Wireless Controller. A beep signal will be audible even if the Wireless
Controller is switched off.
appears in the display).
a second time enables the controls
disappears from the display).
In emergency the stirrer (station) can be
switched off by pressing the "safe STOP"
search button (H) to search for the
®
12