Steinbach Speedclean 75 Bedienungsanleitung Seite 9

EN
Place the base plate and pump in the location where the Pump-
Filter System will be located for normal operation and within reach
of the pool filter and return hoses but with a sufficient safety mar-
gin from the edge of the pool
Attach the filter tank to the base plate as shown.The feet on the bot-
tom of the filter tank fit within the holes provided on the base plate
Insert the tank separator plate inside the main tank in the guides
provided. (Model Speedclean
Filling sand chamber with sand (Picture 6)
Position the filter pump assembly to the location you have dedicated
for its operation. NOTE: Do this before you fill the chamber with sand
as the unit will become heavy and difficult to move around.
Check to ensure that the bottom strainer is correctly positioned.
Check to ensure that the tank separator plate is seated properly.
Fill the sand chamber half full with water.
Pour Quartz Sand with a particle size of 0,40 – 0,80mm into the
SAND FILTER CHAMBER being careful not to allow any sand to en-
ter the FILTERED WATER CHAMBER (see figure).
Speedclean Comfort 50 requires 15 kg of Quartz Sand with a par-
ticle size of 0,4 – 0,8mm.
Speedclean Comfort 75 requires 25 kg of Quartz Sand with a parti-
cle size of 0,4 – 0,8mm.
Securing filter assembly (Abbildung 7,8)
Ensure the main tank seal around the top of the filter tank is in good
condition and securely seated in the
sand.
Locate the upper distributor and press it into the center hole located
under the tank cover. If you are assembling Speedclean
the upper distributor will already be in place.
Carefully place the tank cover onto the filter
should be oriented so that the notch on the cover is aligned with the
matching tab on the filter tank – this ensures proper alignment.
Secure tank cover and filter tank with the tank cover lock ring as-
sembly and tighten with the knob and bolt.
Hooking up the hoses (Picture 9,10,11)
Connecting the filter system
This pool filter system is designed to connect to pools with standard
1¼ or 1½" diameter hose connectors. The type Speedclean Comfort
75 has a 2 ¼" (Ø 32 mm or 38 mm)
your pool has a hose connector size and/or type different than de-
scribed here, you may need to purchase an adapter at your local
pool supply store or hardware retailer.
Since the hoses utilized for filtration and return lines differ for various
types of above-ground pools, the pool-filter connection section is
broken down by pool hose size and type.
Before you begin to connect hoses to the filter and pump, make cer-
tain that no water can flow through the intake or return hoses con-
nected to the pool. Some pools have shut off valves in their intake
and return ports, others do not. If you do not have a shut off valve,
block the ports with a removable plug to prevent water from passing
into and through the hoses.
For Pools with 1¼" or 1½ "Diameter Unthreaded Hoses Picture
12,13
These instructions assume that the pool is already assembled with
hoses attached to the water intake and return ports on the pool.
Sandfilter Speedclean 75/50 | 2015_V1
Comfort 50 only)
grove. Be sure grove is free of
Comfort
tank. The tank cover
hose adapter for Intex® pools. If
Adapter installation
Screw the 1¼"-1½" hose connector into the transparent hair & lint
strainer cover. Make certain that flat gasket "A" is in place before se-
curing.
Pool "Skimmer Hose" Attachment
Attach the hose coming from your
the 1¼"-1½" hose connector extending from the hair & lint
cover.
Secure with a hose clamp.
Pool "Return Hose" Attachment
Lightly lubricate the pool return port on the tank cover with petroleum
jelly.
Attach the pool return hose (inlet of pool) to the pool return port on
the tank cover.
NOTE: Be careful not to secure return hose to the waste/backwash
port.
Secure with a hose clamp.
For Pools that use 2¼" Threaded Hose Connectors Picture 15-18
These instructions assume that the pool is already assembled with
hoses attached to the water intake and return ports on the pool.
1) SHORT INTEX® ADAPTER Installation
Screw the short INTEX® adapter into the transparent hair & lint
strainer cover on the water
is in place before securing.
2) Pool "Skimmer Hose" Attachment
Attach the pool skimmer hose (outlet of pool) to the short INTEX®
adapter. Ensure that the flat gasket "B" is installed between the
short adapter and the face of the hose before securing.
75,
3) LONG INTEX® ADAPTER Installation
Insert O-ring "C" inside long INTEX® adapter. Screw the long
INTEX® adapter onto the pool return port on the tank cover.
4) Pool "Return Hose" Attachment
Screw the pool return hose (Inlet of pool) to the long INTEX® adapt-
er on the tank cover. Ensure that the flat gasket "B" is inserted be-
tween the long INTEX® adapter and the face of the hose before se-
curing
Filter operations
Setting
Filtern
Position 1
Picture 19
Rinse
Position 2
Picture 20
Cirkulation
Position 3
Picture 21
pool's skimmer (outlet of pool) to
pump. Make certain that flat gasket "A"
Complete water flow/function
Function: Vacuum, regular pool filter action. This
is the setting the filter will be set to most of the
time. In this position, water is directed through
the top of the filter where it compresses and flat-
tens down the sand. Contaminants are trapped
by the sand as water makes it way to the bottom
strainer, out of the filter and back to the pool.
Function: Use after backwashing to clean the fil-
ter bed. This should always be done immediately
after backwashing, new sand addition or filter
start-up. In this position, water is directed to the
top of the tank where it flushes the valve while
sending water out the waste line.
Function: circulate water after chemical treat-
ment. This position is used during certain pool
cleanups and chemical treatments when you
don't want the water contaminating the
this position, water is only directed through the
valve back to the pool and does not filter through
the sand.
strainer
sand. In
Page 9 of 64