Additional Safety Rules - Makita DA4000LR Betriebsanleitung

16. Remove adjusting keys and wrenches
Form the habit of checking to see that keys and
adjusting wrenches are removed from tool before
turning it on.
17. Avoid unintentional starting
Don't carry plugged-in tool with finger on switch.
Be sure switch is off when plugging in.
18. Outdoor use extension cords
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
19. Stay alert
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
20. Check damaged parts
Before further use of the tool, a guard or other
part that is damaged should be carefully checked
to determine that it will operate properly and per-
form its intended function. Check for alignment of
moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that
may affect its operation. A guard or other part
that is damaged should be properly repaired or
replaced by an authorized service center unless
otherwise indicated elsewhere in this instruction
manual. Have defective switches replaced by
and authorized service center. Do not use tool if
switch does not turn it on and off.
21. Warning
The use of any other accessory or attachment
other than recommended in this operating
instruction or the catalog may present a risk of
personal injury.
22. Have your tool repaired by an expert
This electric appliance is in accordance with the
relevant safety rules. Repairing of electric appli-
ances may be carried out only by experts other-
wise it may cause considerable danger for the
user.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord. Con-
tact with a ''live'' wire will make exposed metal
parts of the tool ''live'' and shock the operator.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the tool
only when hand-held.
6. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
6
OPERATING INSTRUCTIONS
Installing or removing angle attachment
CAUTION:
Always be sure that the tool is switched off and
unplugged before installing or removing the angle attach-
ment.
The angle head has a spindle on each end. For higher
speed operation, attach the drill chuck to the end marked
"HIGH". The higher speed is better suited for drilling
smaller diameter holes. For lower speed operation,
attach the drill chuck to the end marked "LOW". The
lower speed is best utilized for drilling larger diameter
holes. (Fig. 1)
The tool is factory assembled with the chuck on spindle
end marked "HIGH".
To change to the "LOW" speed, proceed as follows:
To remove the drill chuck, first open the chuck jaws com-
pletely and place the chuck key in one of the key holes.
(Fig. 2)
Remove the chuck remaining bolt through the chuck
opening by turning it counterclockwise with the hex
wrench. (Fig. 3)
CAUTION:
The drill chuck and the bolt are assembled each other.
Turn the bolt counterclockwise about 10 times so that
they can be removed together.
Loosen the bolts of the joint by the hex wrench and
remove the angle housing, the joint and the socket.
(Fig. 4)
To install the socket and the joint, fit the socket to the
spindle so that the two faces are fitted perfectly. Then
install the joint. For higher speed operation, fit the angle
housing marked "LOW" to the joint.
For lower speed operation, fit the angle housing marked
"HIGH" to the joint. (Fig. 5)
Rotate the angle housing to the desired position. Tighten
the bolt with the hex wrench firmly. And retighten the
another bolt firmly again. (Fig. 6)
CAUTION:
Be sure to tighten the two bolts firmly, or it may present a
risk of injury to persons.
ENB001-1
Slide the drill chuck to the spindle so that the two faces
are fitted perfectly. Holding the drill chuck with the chuck
key, tighten the bolt (for installing the drill chuck) clock-
wise with the hex wrench firmly. (Fig. 7 & 8)
The tool may be converted to a conventional straight
drive drill by installing the drill chuck without the angle
attachment. (Fig. 9)
Side grip (auxiliary handle)
CAUTION:
Always use the side grip and hold it with both hands to
ensure operating safety.
Use of it without angle attachment (Fig. 10)
Screw the side handle for the tool on the tool barrel
securely. The side grip can be installed on either side of
the tool, whichever is convenient.
Use of it with angle attachment
Screw the side grip for the angle attachment on the angle
housing. Then tighten the side grip by turning clockwise
at the desired position. (Fig. 11)