Functional Description - Makita HP333D Betriebsanleitung

Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
Never recharge a fully charged battery car-
2.
tridge. Overcharging shortens the battery
service life.
Charge the battery cartridge with room tem-
3.
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
WULGJH ¿UPO\ ZKHQ LQVWDOOLQJ RU UHPRYLQJ EDWWHU\
cartridge. )DLOXUH WR KROG WKH WRRO DQG WKH EDWWHU\
FDUWULGJH ¿UPO\ PD\ FDXVH WKHP WR VOLS RII \RXU KDQGV
DQG UHVXOW LQ GDPDJH WR WKH WRRO DQG EDWWHU\ FDUWULGJH
DQG D SHUVRQDO LQMXU\
Fig.1: 1. Red indicator 2. Button 3. Battery cartridge
7R UHPRYH WKH EDWWHU\ FDUWULGJH VOLGH LW IURP WKH WRRO
ZKLOH VOLGLQJ WKH EXWWRQ RQ WKH IURQW RI WKH FDUWULGJH
7R LQVWDOO WKH EDWWHU\ FDUWULGJH DOLJQ WKH WRQJXH RQ WKH
EDWWHU\ FDUWULGJH ZLWK WKH JURRYH LQ WKH KRXVLQJ DQG VOLS
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
XSSHU VLGH RI WKH EXWWRQ LW LV QRW ORFNHG FRPSOHWHO\
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not,
LW PD\ DFFLGHQWDOO\ IDOO RXW RI WKH WRRO FDXVLQJ LQMXU\ WR
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
QRW EHLQJ LQVHUWHG FRUUHFWO\
Battery protection system
7KH WRRO LV HTXLSSHG ZLWK D EDWWHU\ SURWHFWLRQ V\VWHP
This system automatically cuts off power to the motor to
H[WHQG EDWWHU\ OLIH
The tool will automatically stop during operation if the
WRRO DQGRU EDWWHU\ DUH SODFHG XQGHU RQH RI WKH IROORZLQJ
FRQGLWLRQV
Overloaded:
The tool is operated in a manner that causes it to draw
DQ DEQRUPDOO\ KLJK FXUUHQW
In this situation, turn the tool off and stop the application
WKDW FDXVHG WKH WRRO WR EHFRPH RYHUORDGHG 7KHQ WXUQ
the tool on to restart.
,I WKH WRRO GRHV QRW VWDUW WKH EDWWHU\ LV RYHUKHDWHG ,Q WKLV
VLWXDWLRQ OHW WKH EDWWHU\ FRRO EHIRUH WXUQLQJ WKH WRRO RQ DJDLQ
Low battery voltage:
7KH UHPDLQLQJ EDWWHU\ FDSDFLW\ LV WRR ORZ DQG WKH WRRO ZLOO QRW
RSHUDWH ,I \RX WXUQ WKH WRRO RQ WKH PRWRU UXQV DJDLQ EXW VWRSV
VRRQ ,Q WKLV VLWXDWLRQ UHPRYH DQG UHFKDUJH WKH EDWWHU\
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
Fig.2: 1. Indicator lamps 2. &KHFN EXWWRQ
3UHVV WKH FKHFN EXWWRQ RQ WKH EDWWHU\ FDUWULGJH WR LQGL-
FDWH WKH UHPDLQLQJ EDWWHU\ FDSDFLW\ 7KH LQGLFDWRU ODPSV
light up for a few seconds.
Indicator lamps
Lighted
NOTE: Depending on the conditions of use and the
DPELHQW WHPSHUDWXUH WKH LQGLFDWLRQ PD\ GLIIHU VOLJKWO\
from the actual capacity.
Switch action
Fig.3: 1. Switch trigger
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
To start the tool, simply pull the switch trigger. Tool
VSHHG LV LQFUHDVHG E\ LQFUHDVLQJ SUHVVXUH RQ WKH VZLWFK
trigger. Release the switch trigger to stop.
Lighting up the front lamp
Fig.4: 1. Lamp
CAUTION:
Do not look in the light or see the
source of light directly.
3XOO WKH VZLWFK WULJJHU WR OLJKW XS WKH ODPS 7KH ODPS
NHHSV RQ OLJKWLQJ ZKLOH WKH VZLWFK WULJJHU LV EHLQJ SXOOHG
The lamp goes out approximately 10 seconds after
releasing the switch trigger.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
7 ENGLISH
Remaining
capacity
Off
75% to 100%
50% to 75%
25% to 50%
0% to 25%