Comsafe HolyTec Bedienungsanleitung Seite 3

01--24-new HolyTec Instruct 4.2010:1 – 8
GB USA
Operating instructions for
HolyTec
Attention: Please read this operating instruction careful-
ly, before you operate the lock or try to program a new
Master – and/or Usercode. We can not accept any liabi-
lity for the loss of property due to functional disorder
because of faulty programming or use of violence or
improper use and neither for damage caused by this
You can open your new safe by entering the
Mastercode 0-0-0-0-0-0.
We strongly advise you to change the Mastercode.
First time use:
Remove the battery cover on the inside of the door by
taking out the screw;
Insert Four 1.5 Volt AA batteries. (Please take care of
polarity);
On the display it should say "SCURE" first followed by
"GOOD";
Close the battery cover.
General remarks:
If you have typed a wrong button, you can always press
the " * " button to undo this action;
To check the battery, press the "# " button. If "BATT-H"
appears on the display, the batteries are good, if "BATT-
L" appears, the batteries need to be changed. If you
don't want the numbers of the code to appear on the dis-
play, push the " * " button, before you enter your code.
On the display the numbers won't appear, instead you
will see "------".
If you programm a new code, always test the new code
while the door is open. We supply the safe without bat-
teries. We strongly advise to use branded High Energy
alkaline batteries. Never leave the manual and the emer-
gency keys in the safe!!
Closing the safe – programm Usercode:
Whilst the door is open, enter the desired code (min. 3,
max. 6 digits);
Confirm the code by pushing the " # " button;
On the display "CLOSED".will appear;
The code will show up on the display for 5 seconds;
By using the programmed code, the door can now be
closed.
Mobil-5.06 print
Opening the safe by using the Usercode:
ENGLISH
Enter the programmed Usercode (min. 3 digits, max.
6 digits);
Confirm the code by pushing the "# " button;
On the display "OPEN" will appear;
The door will open.
First time opening by using the
Mastercode:
Push the " # " button twice;
Enter the Mastercode (Factory-code: 0-0-0-0-0-0);
On the display "OPEN" will appear;
The door will open.
Changing the Mastercode:
Push the " * " button twice;
On the display "PROG" will appear;
Enter the following code: 8-4-2-6-2-7;
Confirm the code by pushing the " # " button;
On the display "OLD" will appear;
Enter the Mastercode (Factory-code: 0-0-0-0-0-0);
Confirm the code by pushing the " # " button;
On the display "NEW" will appear;
Enter the desired new Mastercode (has to be 6 digits!);
Confirm the new Mastercode by pushing the
" # " button;
On the display "AGAIN" will appear;
Enter the desired new Mastercode (has to be 6 digits!)
for the 2nd time;
Confirm the new Mastercode code by pushing the " # "
button;
On the display "GOOD" will appear;
The Mastercode has successfully been changed.
Locking device time when entering the
wrong code:
If you enter a wrong code "E-CODE" appears on the dis-
play;
Now you can try 3 more times to enter the correct code;
After 4 wrong entries you can see on the display
"hold-5";
Now the electronic doesn't respond on any entries for
5 minutes;
After 5 minutes are over, one can start trying codes
again.
Emergency opening with emergency key:
Remove the cover below the key pad;
Insert the emergency key (comes with the safe);
Turn the emergency key to the right or the left;
Now you can open the door of the safe.
22.04.2010
Attention:
Your new Safe and it's content aren't automatically
insured. Please write a letter to your insurance
about the insurance value you'd like.
18:59 Uhr
5
COMSAFE HOLYTEC
Seite 5