B Allgemeine Lizenzbedingungen - Siemens SINAMICS V20 Kompaktbetriebsanleitung

Liste der Warncodes
Warnung Beschreibung
A501 Stromgrenzwert
A502 Überspannungsgrenzwert
A503 Unterspannungsgrenzwert
A504 Übertemperatur Umrichter
A505 Umrichter I
A506 Warnung bei IGBT-Junction-
Temperaturanstieg
A507 Verlust des Umrichtertemperatursignals
A511 Übertemperatur Motor I
A535 Überlast Bremswiderstand
A541 Motordatenidentifikation aktiv
Warnungen können nicht quittiert werden. Sie werden automatisch gelöscht, wenn die Ursache für die Warnung behoben
wurde.
B Allgemeine Lizenzbedingungen
For Resellers: In order to avoid infringements of the license conditions by the reseller or the buyer these instructions and
license conditions and accompanying CD – if applicable - have to be forwarded to the buyers.
1) Siemens License Conditions
General License Conditions for Software Products for Automation and Drives
(2011-08-01)
1 Supply of Software to Licensee and Granting of Rights to use the Software
1.1 These General License Conditions shall exclusively apply to the delivery of Software for Automation and Drives to the
Licensee. General terms and conditions of the Licensee shall apply only where expressly accepted in writing by us. The
scope of delivery of the Software shall be determined by the congruent mutual written declarations of both parties. We shall
grant the Licensee rights to use the software specified in the Confirmation of Order or, if the Licensee does not receive a
Confirmation of Order, the software specified in the Certificate of License or that specified in the Software Product Sheet, if
the Licensee is instead submitted a Software Product Sheet (hereinafter referred to as "SW"). The Certificate of License and
the Software Product Sheet shall be collectively referred to as "CoL" hereinafter. The Licensee shall be submitted the CoL
when the SW is supplied or in conjunction with the delivery bill. The way in which the SW is supplied is also derived directly
from the Confirmation of Order or from the SW purchase order number contained in the Confirmation of Order, in
conjunction with the associated order data of our catalog valid at the time of the Confirmation of Order (hereinafter
collectively referred to as "Order Data"), or from the CoL. If the Licensee does not receive a data medium, it shall be
authorized to copy the SW already available to it to the extent necessary to exercise the rights to use the SW granted to it.
The aforesaid shall apply, mutatis mutandis, to electronic supply of the software (downloading). Where reference is made to
the Order Data or the CoL in these General License Conditions, the reference to the CoL is of significance if the Licensee
has not received a Confirmation of Order. In any case, the data contained in the Order Data is also contained in the CoL.
1.2 The Documentation relating to the SW (hereinafter referred to as "Documentation") shall be purchased separately,
unless either the Order Data or CoL contains a stipulation stating that it belongs to the scope of delivery. If the Licensee is
authorized to copy the SW in accordance with Clause 1.1, this shall also apply to the Documentation provided that it is
included in the scope of delivery.
1.3 In the event that we submit a License Key to the Licensee, which unlocks the SW (hereinafter referred to as "License
Key"), this License Key must also be installed.
1.4 The rights granted to the Licensee with respect to the SW are based on the License Type (see Section 2) and the
Software Type (see Section 3). The license and Software Types are detailed in the Order Data or CoL. If the SW is supplied
electronically or if copying rights are granted for it, the rights and duties specified in these General License Conditions shall
apply to the legitimately generated copies.
1.5 If the Licensee is legitimately in possession of a previous SW version/release (hereinafter referred to as "Previous
Version"), the Licensee shall be authorized to exercise the rights to use the SW granted to it either with respect to the SW or
30
t
2
t
2
Warnung Beschreibung
A600 Warnung vor RTOS-Datenverlust
A910 Vdc-max-Regler deaktiviert
A911 Vdc-max-Regler aktiv
A912 Vdc-min-Regler aktiv
A921 Parameter für Analogausgang nicht korrekt festge-
legt
A922 Keine Last an Umrichter angelegt
A923 JOG links und JOG rechts angefordert
A930 Kavitationsschutzwarnung
A936 PID-Selbstoptimierung aktiv
A952 Förderbandfehler erkannt
Frequenzumrichter SINAMICS V20
A5E37281083, 02/2016