Elektro-Automatik EL 9080-170 B Betriebsanleitung Seite 99

TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.1.4 Symbols and warnings ..................................5
1.2 Warranty .........................................................5
1.3 Limit of liability ................................................5
1.4 Disposal of equipment ...................................6
1.5 Product key ....................................................6
1.6 Intended usage ..............................................6
1.7 Safety .............................................................7
1.7.1 Safety notices .................................................7
1.7.2 Responsibility of the user...............................7
1.7.3 Responsibility of the operator .......................8
1.7.4 User requirements .........................................8
1.7.5 Alarm signals ..................................................9
1.8 Technical data ................................................9
1.8.1 Approved operating conditions ......................9
1.8.2 General technical data ...................................9
1.8.3 Specific technical data .................................10
1.8.4 Views (3U models) .......................................18
1.8.5 Views (6U models) .......................................21
1.8.6 Control elements ..........................................24
1.9 Construction and function ............................25
1.9.1 General description ......................................25
1.9.2 Block diagram ..............................................25
1.9.3 Scope of delivery .........................................26
1.9.4 Accessories ..................................................26
1.9.5 Options .........................................................26
1.9.6 The control panel (HMI) ...............................27
1.9.7 USB port (type B, rear side) ........................30
1.9.8 Interface module slot ...................................30
1.9.9 Analog interface ...........................................30
1.9.10 "Share" connector ........................................31
1.9.11 "Sense" connector (remote sensing) ...........31
1.9.12 Master-Slave bus .........................................31
2
INSTALLATION &
COMMISSIONING
2.1 Transport and storage .................................32
2.1.1 Transport ......................................................32
2.1.2 Packaging ....................................................32
2.1.3 Storage .........................................................32
2.2 Unpacking and visual check ........................32
2.3 Installation ....................................................32
2.3.1 Safety procedures before installation and
use ................................................................32
2.3.2 Preparation ...................................................33
2.3.3 Installing the device .....................................33
2.3.4 Connection to DC sources (3U models) .....34
2.3.5 Connection to DC sources (6U models) .....35
EA Elektro-Automatik GmbH
Helmholtzstr. 31-37 • 41747 Viersen
Germany
2.3.6
2.3.7
2.3.8
2.3.9
2.3.10 Installation of an interface module ...............37
2.3.11
2.3.12 Initial commission .........................................38
2.3.13 Commission after a firmware update or a
3
OPERATION AND APPLICATION
3.1
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.4
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.4.8
3.4.9
3.4.10 Recording to USB stick (logging) ................56
3.5
3.5.1
3.5.2
3.5.3
3.5.4
3.6
3.6.1
3.6.2
3.7
3.8
3.9
3.10
3.10.1 Introduction...................................................67
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
EL 9000 B Series
Grounding of the DC input ...........................36
Connecting the "Share" bus ........................36
Connection of remote sensing ....................36
Connecting the USB port (rear side) ...........37
Connecting the analog interface .................38
long period of non use .................................38
Personal safety ............................................39
Operating modes .........................................39
Voltage regulation / Constant voltage .........39
Current regulation / constant current / current
limitation .......................................................40
Resistance regulation / constant resistance 40
Power regulation / constant power / power
limitation .......................................................40
Dynamic characteristics and stability crite-
ria ..................................................................41
Alarm conditions ..........................................42
Power Fail ...................................................42
Overtemperature ..........................................42
Overvoltage ..................................................42
Overcurrent ..................................................42
Overpower ....................................................42
Manual operation .........................................43
Powering the device ....................................43
Switching the device off ...............................43
Configuration via MENU ..............................43
Adjustment limits ..........................................53
Changing the operating mode .....................53
Manual adjustment of set values .................54
Switching the main screen view ..................54
The meter bars .............................................55
Switching the DC input on or off ..................55
Remote control .............................................57
General .........................................................57
Controls locations ........................................57
Remote control via a digital interface ..........57
Remote control via the analog interface
(AI) ................................................................58
Alarms and monitoring .................................62
Definition of terms ........................................62
Device alarm and event handling ................62
Control panel (HMI) lock ..............................65
Limits lock .....................................................65
Loading and saving a user profile ...............66
The function generator.................................67
www.elektroautomatik.de
ea1974@elektroautomatik.de
Page 3