Specifications; Additional Safety Rules; Functional Description; Operation - Makita UB1100 Betriebsanleitung

ENGLISH
(Original instructions)
1 Switch trigger
2 Lock button
3 Speed control screw
4 Higher
5 Lower

SPECIFICATIONS

Model
Capacities
Air pressure (water column) .................................................................... 5.5 kPa
Max. air volume ....................................................................................... 2.8 m
–1
No load speed (min ) ................................................................................ 16,000
Overall length ............................................................................................. 480 mm
Net weight................................................................................................... 1.9 kg
Safety class ................................................................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for blowing dust.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

ADDITIONAL SAFETY RULES

1. Always use protective goggles, a cap and mask
when using the blower.
2. Never point the nozzle at anyone in the vicinity
when using the blower.
3. Always use the dust bag when collecting dust,
chips and the like.
4. Do not collect still smoldering cigarette ashes,
freshly cut metals shavings, screws, nails and
the like. Warning – Electric shock could occur if
used on wet surfaces. Do not expose to rain.
Store indoors.
5. Never block suction inlet and/or blower outlet.
Increased motor revolution may cause danger-
ous fan breakage.
6. The blower is not intended for use by young chil-
dren or infirm persons without supervision.
7. Young children should be supervised to ensure
that they do not play with the blower.
SAVE THESE INSTRUCTIONS.
Explanation of general view
6 Nozzle
7 Blower outlet
8 Dust bag
9 Suction inlet
10 Fastener

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
ENE018-1
Switch action
CAUTION:
ENF002-2
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
For UB1100 (Fig. 1)
To start the tool, simply pull the switch trigger. Release
the trigger to stop.
For continuous operation, pull the switch trigger and then
GEA010-1
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
For UB1101 (Fig. 2)
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
ENB017-1
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
A speed control screw is provided so that maximum tool
speed can be limited (variable). Turn the speed control
screw clockwise for higher speed, and counterclockwise
for lower speed.

OPERATION

Blowing (Fig. 3)
For dust blowing, attach nozzle to blower outlet, turning
clockwise to lock it in place.
Dust suction (Fig. 4 & 5)
NOTE:
• Dust bags are optional accessories in some countries.
For dust suction, fit nozzle onto suction inlet and dust
bag onto blower outlet.
After the bag fills with dust, empty the contents of the
dust bag into a dust bin by releasing the fastener.
11 Limit mark
12 Brush holder cap
13 Screwdriver
UB1100
3
/min.
/II
UB1101
0 – 5.5 kPa
3
0 – 2.8 m /min.
0 – 16,000
480 mm
1.9 kg
/II
3