Makita DTD171 Betriebsanleitung Seite 8

Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Fig.4: 1. Lamp
Fig.5: 1. Button
Pull the switch trigger to turn on the lamp. To turn off,
UHOHDVH LW 7KH ODPS JRHV RXW DSSUR[LPDWHO\  VHFRQGV
after releasing the switch trigger.
To keep the lamp off, turn off the lamp status. To turn off
WKH ODPS VWDWXV ¿UVW SXOO DQG UHOHDVH WKH VZLWFK WULJJHU
And then press the button
To turn on the lamp status again, press the but-
ton DJDLQ VLPLODUO\
NOTE: :KHQ WKH WRRO LV RYHUKHDWHG WKH OLJKW ÀDVKHV
IRU RQH PLQXWH DQG WKHQ WKH /(' GLVSOD\ JRHV RII ,Q
this case, cool down the tool before operating again.
NOTE: 7R FRQ¿UP WKH ODPS VWDWXV SXOO WKH WULJJHU
:KHQ WKH ODPS OLJKWV XS E\ SXOOLQJ WKH VZLWFK WULJJHU
the lamp status is ON. When the lamp does not come
on, the lamp status is OFF.
NOTE: 8VH D GU\ FORWK WR ZLSH WKH GLUW RII WKH OHQV RI
the lamp. Be careful not to scratch the lens of lamp, or
LW PD\ ORZHU WKH LOOXPLQDWLRQ
Reversing switch action
Fig.6: 1. Reversing switch lever
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. Changing the
GLUHFWLRQ RI URWDWLRQ EHIRUH WKH WRRO VWRSV PD\ GDP-
age the tool.
CAUTION:
When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
Changing the application mode
What's the application mode?
The application mode is the variation of the driving
URWDWLRQ DQG LPSDFW ZKLFK DUH DOUHDG\ SUHVHW LQ WKH WRRO
%\ FKRRVLQJ D VXLWDEOH DSSOLFDWLRQ PRGH GHSHQGLQJ RQ
WKH ZRUN \RX FDQ DFFRPSOLVK TXLFNHU ZRUN DQGRU PRUH
EHDXWLIXO ¿QLVK
This tool features following application modes:
Impact force
• Max
• Hard
• Medium
• Soft
within 10 seconds.
Assist type
• Wood mode
• Bolt mode
• T mode (1)
• T mode (2)
7KH DSSOLFDWLRQ PRGH FDQ EH FKDQJHG E\ WKH EXW-
ton , , or the quick mode-switching button.
Fig.7: 1. Quick mode-switching button
2. Button
%\ UHJLVWHULQJ D FHUWDLQ DSSOLFDWLRQ PRGH WR WKH WRRO
\RX FDQ VZLWFK WR WKH UHJLVWHUHG DSSOLFDWLRQ PRGH E\
MXVW SUHVVLQJ WKH TXLFN PRGHVZLWFKLQJ EXWWRQ TXLFN
mode-switching function).
NOTE: When none of the lamp on the panel is lit,
pull the switch trigger once before pressing the quick
mode-switching button.
NOTE: You will not be able to change the application
PRGH LI \RX GR QRW RSHUDWH WKH WRRO IRU DSSUR[LPDWHO\
one minute. In this case, pull the switch trigger
once and press the
mode-switching button.
NOTE: Refer to "Registering the application mode"
in "Quick mode-switching function" section for how to
register the application mode.
Quick mode-switching button
The function of the quick mode-switching button varies
GHSHQGLQJ RQ ZKHWKHU \RX KDYH UHJLVWHUHG WKH DSSOLFD-
tion mode to the tool.
Fig.8: 1. Quick mode-switching button
When the application mode is not registered:
7KH OHYHO RI LPSDFW IRUFH FKDQJHV HYHU\ WLPH \RX SUHVV
the quick mode-switching button. The front lamps on
ERWK VLGHV ZLOO ÀDVK RQFH ZKHQ WKH LPSDFW IRUFH LV
FKDQJHG E\ SUHVVLQJ WKH TXLFN PRGHVZLWFKLQJ EXWWRQ
When the application mode is registered:
The tool switches between the registered application
PRGH DQG FXUUHQW DSSOLFDWLRQ PRGH HYHU\ WLPH \RX SUHVV
the quick mode-switching button. The front lamps on
ERWK VLGHV ZLOO ÀDVK RQFH ZKHQ WKH DSSOLFDWLRQ PRGH LV
FKDQJHG E\ SUHVVLQJ WKH TXLFN PRGHVZLWFKLQJ EXWWRQ
NOTE: When the lamp status is off, the lamps will not
ÀDVK HYHQ ZKHQ WKH DSSOLFDWLRQ PRGH LV FKDQJHG E\
pressing the quick mode-switching button.
NOTE: Refer to "Registering the application mode"
in "Quick mode-switching function" section for how to
register the application mode.
Disabling the quick mode-switching button
You can also disable the quick mode-switching button. After
disabling, the quick mode-switching button will not work for
changing the impact force and switching the application mode.
To disable the quick mode-switching button, press and
hold the quick mode-switching button and the but-
ton at the same time until the all lamps on the panel
blink.
To resume the quick mode-switching button, perform
the same procedure as above again.
8 ENGLISH
3. Button
button, button, or quick