Makita DTD171 Betriebsanleitung Seite 10

Changing assist type
7KLV WRRO HPSOR\V DVVLVW IXQFWLRQ WKDW RIIHUV VHYHUDO HDV\WR
use application modes for driving screws with good control.
7KH W\SH RI WKH DSSOLFDWLRQ PRGH FKDQJHV HYHU\ WLPH
\RX SUHVV WKH EXWWRQ .
Application mode
(Assist type displayed
on panel)
Wood mode *1
Bolt mode (reverse rota-
tion auto stop) *1 *2
T mode (1) *1
(The tool stops rotating
soon after impact starts.)
T mode (2) *1
 $XWRPDWLF VSHHG FRQWURO ZRUNV RQO\ ZKHQ WKH VZLWFK WULJJHU LV IXOO\ SXOOHG
 5HYHUVH URWDWLRQ DXWR VWRS ZRUNV RQO\ ZKHQ WKH WRRO LV GULYLQJ LQ FRXQWHUFORFNZLVH URWDWLRQ
NOTE: When none of the lamp on the panel is lit, pull the switch trigger once before pressing the button
NOTE: $OO ODPSV RQ WKH VZLWFK SDQHO JR RXW ZKHQ WKH WRRO LV WXUQHG RII WR VDYH WKH EDWWHU\ SRZHU 7KH W\SH RI WKH
DSSOLFDWLRQ PRGH FDQ EH FKHFNHG E\ SXOOLQJ WKH VZLWFK WULJJHU WR WKH H[WHQW WKDW WKH WRRO GRHV QRW RSHUDWH
Quick mode-switching function
What you can do with the quick mode-
switching function
The quick mode-switching function saves the time for changing
WKH DSSOLFDWLRQ PRGH RI WKH WRRO <RX FDQ VZLWFK WR \RXU GHVLUHG
DSSOLFDWLRQ PRGH E\ MXVW SUHVVLQJ WKH TXLFN PRGHVZLWFKLQJ
button. It is helpful when doing a repetitive work which requires
WR VZLWFK EHWZHHQ WZR DSSOLFDWLRQ PRGHV DOWHUQDWHO\
EXAMPLE ,I \RX KDYH D ZRUN WR XVH 7 PRGH DQG PD[
impact force, register the max impact force for quick
PRGHVZLWFKLQJ IXQFWLRQ 2QFH UHJLVWHU LW \RX FDQ VZLWFK
WR WKH PD[ LPSDFW IRUFH IURP 7 PRGH E\ MXVW RQH FOLFN RI
WKH TXLFN PRGHVZLWFKLQJ EXWWRQ $OVR \RX FDQ UHWXUQ WR 7
PRGH E\ SUHVVLQJ WKH TXLFN PRGHVZLWFKLQJ EXWWRQ DJDLQ
Even if the tool is in other application mode than T
mode, pressing the quick mode-switching button
FKDQJHV WR PD[ LPSDFW IRUFH ,W LV FRQYHQLHQW IRU \RX
WR UHJLVWHU D DSSOLFDWLRQ PRGH WKDW \RX IUHTXHQWO\ XVH
Maximum blows
-1
3,800 min (/min) This mode helps to prevent a screw from falling at
the beginning of driving. The tool drives a screw
ZLWK ORZVSHHG URWDWLRQ DW ¿UVW $IWHU WKH WRRO VWDUWV
to impact, the rotation speed increases and reaches
the maximum speed.
-1
3,800 min (/min) This mode helps to prevent a bolt from falling off.
When loosening a bolt with the tool driving in coun-
WHUFORFNZLVH URWDWLRQ WKH WRRO DXWRPDWLFDOO\ VWRSV
after the bolt/nut gets enough loosened. The stroke
of the switch trigger to reach maximum speed will
become short in this mode.
– This mode helps to prevent the screws from
over-tightening. It also accomplishes quick oper-
DWLRQ DQG JRRG ¿QLVK DW WKH VDPH WLPH 7KH WRRO
drives a screw with high-speed rotation and stops
soon after the tool starts to impact.
NOTE:
The timing to stop the driving varies depending
on the type of the screw and material to be
driven. Make a test driving before using this
mode.
-1
2,600 min (/min) This mode helps to prevent the screws from
breakage and stripping. It also accomplishes quick
RSHUDWLRQ DQG JRRG ¿QLVK DW WKH VDPH WLPH 7KH WRRO
drives a screw with high-speed rotation and slows
down the rotation when the tool starts to impact.
NOTE:
Release the switch trigger as soon as the tight-
HQLQJ ¿QLVKHG WR DYRLG RYHUWLJKWHQLQJ
<RX FDQ FKDQJH WKH DVVLVW W\SH ZLWKLQ DSSUR[LPDWHO\
one minute after releasing the switch trigger or press-
ing the button ,
button.
Fig.10: 1. Button
Feature
You can choose one of following application modes for
quick mode-switching function:
Impact force
• Max
• Hard
• Medium
• Soft
Assist type
• Wood mode
• Bolt mode
• T mode (1)
• T mode (2)
Registering application mode
7R XVH WKH TXLFN PRGHVZLWFKLQJ IXQFWLRQ UHJLVWHU \RXU
desired application mode to the tool beforehand.
1.
With the button
application mode.
10 ENGLISH
, or the quick mode-switching
Purpose
Tightening long screws.
Loosening bolts.
Driving self-drilling
screws to a thin metal
SODWH ZLWK JRRG ¿QLVK
Driving self-drilling
screws to a thick metal
SODWH ZLWK JRRG ¿QLVK
.
or  FKRRVH \RXU GHVLUHG