Operation - Makita DTD171 Betriebsanleitung

2. Press and hold the button
mode-switching button at the same time until the custom-
ize lamp and the lamp of desired application mode blinks.
Fig.11: 1. Quick mode-switching button 2. Customize lamp
NOTE: You can overwrite the current application mode
ZLWK QHZ RQH E\ SHUIRUPLQJ WKH SURFHGXUH DERYH
Using the quick mode-switching function
When the tool is in the mode that is not registered, press the
quick mode-switching button to switch to the registered applica-
tion mode. The tool switches between the registered application
PRGH DQG ODVW DSSOLFDWLRQ PRGH HYHU\ WLPH \RX SUHVV WKH TXLFN
PRGHVZLWFKLQJ EXWWRQ 7KH IURQW ODPSV RQ ERWK VLGHV ZLOO ÀDVK
once when switching to the registered application mode.
NOTE: The customize lamp will light up when the
application mode registered to the tool is chose.
Cancelling the quick mode-switching function
Press and hold the button
ing button at the same time until the customize lamp
and all impact force grade lamps blink.
NOTE: After cancelling the quick mode-switching function, the
quick mode-switching button works for changing the impact force.
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/socket bit
Fig.12
8VH RQO\ GULYHU ELWVRFNHW ELW WKDW KDV LQVHUWLQJ SRUWLRQ VKRZQ
LQ WKH ¿JXUH 'R QRW XVH DQ\ RWKHU GULYHU ELWVRFNHW ELW
For tool with shallow driver bit hole
A=12mm
B=9mm
For tool with deep driver bit hole
A=17mm
B=14mm
A=12mm
B=9mm
Procedure 1
For tool without one-touch type sleeve
Fig.13: 1. Driver bit 2. Sleeve
To install the driver bit, pull the sleeve in the direction of the
arrow and insert the driver bit into the sleeve as far as it will go.
Then release the sleeve to secure the driver bit.
For tool with one-touch type sleeve
To install the driver bit, insert the driver bit into the
sleeve as far as it will go.
and the quick
and quick mode-switch-
8VH RQO\ WKHVH W\SH RI GULYHU ELW
Follow the procedure 1. (Note)
%LWSLHFH LV QRW QHFHVVDU\
7R LQVWDOO WKHVH W\SHV RI GULYHU
bits, follow the procedure 1.
7R LQVWDOO WKHVH W\SHV RI GULYHU
bits, follow the procedure 2.
1RWH %LWSLHFH LV QHFHVVDU\
for installing the bit.
Procedure 2
In addition to Procedure 1, insert the bit-piece into the
sleeve with its pointed end facing in.
Fig.14: 1. Driver bit 2. Bit-piece 3. Sleeve
To remove the driver bit, pull the sleeve in the direction
of the arrow and pull the driver bit out.
NOTE: If the driver bit is not inserted deep enough into
the sleeve, the sleeve will not return to its original posi-
WLRQ DQG WKH GULYHU ELW ZLOO QRW EH VHFXUHG ,Q WKLV FDVH WU\
re-inserting the bit according to the instructions above.
NOTE: :KHQ LW LV GLI¿FXOW WR LQVHUW WKH GULYHU ELW SXOO WKH
sleeve and insert it into the sleeve as far as it will go.
NOTE: After inserting the driver bit, make sure that it
LV ¿UPO\ VHFXUHG ,I LW FRPHV RXW GR QRW XVH LW
Installing hook
CAUTION:
When installing the hook, always
VHFXUH LW ZLWK WKH VFUHZ ¿UPO\ ,I QRW WKH KRRN PD\
FRPH RII IURP WKH WRRO DQG UHVXOW LQ WKH SHUVRQDO LQMXU\
Fig.15: 1. Groove 2. Hook 3. Screw
7KH KRRN LV FRQYHQLHQW IRU WHPSRUDULO\ KDQJLQJ WKH WRRO
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.

OPERATION

Fig.16
7KH SURSHU IDVWHQLQJ WRUTXH PD\ GLIIHU GHSHQGLQJ XSRQ
the kind or size of the screw/bolt, the material of the
workpiece to be fastened, etc. The relation between fas-
WHQLQJ WRUTXH DQG IDVWHQLQJ WLPH LV VKRZQ LQ WKH ¿JXUHV
Proper fastening torque for standard bolt
N•m
(kgf•cm)
140
(1428)
120
(1224)
100
(1020)
80
(816)
2
60
(612)
40
(408)
20
(204)
0
1. Fastening time (second) 2. Fastening torque
11 ENGLISH
M16
M14
M16
M12
M14
M10
M12
M8
M10
M8
1 2
1