Safety Warnings And Precautions; Product Description And Intended Use - Nice Era Serie Installierungs-Und Gebrauchsanleitungen Und Hinweise

ENGLISH
1
SAFETY WARNINGS AND
PRECAUTIONS
1.1 - Safety warnings
l Attention! – Important safety instructions: keep
these instructions.
l Attention! – It is important to follow these instruc-
tions to ensure safety. Therefore, read this manual
carefully before beginning work.
1.2 - Installation warnings
l All product installation, connection, programming and
maintenance operations must be performed exclusive-
ly by a qualified and skilled technician, in observance of
laws, standards and local regulations and the instructions
in this manual.
l Before installation, ensure that this specific product is
suitable for the automation of your shutter (see chapter 3).
l All product installation and maintenance operations
must be performed with the automation disconnected from
the power mains. As a precaution, affix a notice with the
text "WARNING: MAINTENANCE IN PROGRESS" on the
disconnect device.
l Before starting installation procedures, move away all
electric cables not involved in the work and deactivate all
mechanisms not required for motor-driven operation of
the shutter.
l If the product is installed at a height of less than 2.5 m
from the floor or other support surface, the moving parts
must be protected with a suitable covering, to avoid inad-
vertent access. For protection, refer to the instruction man-
ual of the shutter, ensuring that future access for mainte-
nance purposes is guaranteed.
l On sun awnings, a minimum horizontal distance of 40
cm must be guaranteed between the awning completely
open and any fixed object positioned in front.
1 – English
l During installation, handle the product with care, avoid-
ing the risk of crushing, impact, dropping or contact with
any type of liquid, do not insert sharp objects in the motor,
do not drill or insert screws on the motor exterior and do
not place the product in the vicinity of heat sources or na-
ked flames (fig. 2). This may damage product and cause
malfunctions, fire or hazardous situations. If this occurs,
suspend installation immediately and contact the Nice
Technical Assistance.
l Do not disassemble the product in excess of the opera-
tions envisaged in this manual.
l Never make any modifications to part of the product oth-
er than those specified in this manual. Operations other
than as specified can only cause malfunctions. The man-
ufacturer declines all liability for damage caused by ma-
keshift modifications to the product.
l The power supply cable for the motor is made from
PVC and is suitable for use in indoor environments. For
use in other environments, protect the entire length of the
cable by inserting it inside a dedicated sheath for protect-
ing electrical cables.
l The unit's power cable may not be replaced. If the cable
is damaged, the device must be scrapped.
l Do not use multiple control devices for a single tubular
motor or a single control device for multiple tubular mo tors
(fig. 3). If necessary, use the special Nice accessory "TTE".
l During system set-up, keep all persons far from the
shutter when moving.
l To control the product, use exclusively hold-to-run type
pushbuttons, i.e. which must remain pressed for the en-
tire manoeuvre.
1.3 - Operation warnings
l This product is not intended to be used by persons (in-
cluding children) whose physical, sensorial or mental ca-
pacities are reduced, or who lack the necessary experi-
ence or skill.
l Do not allow children to play with fixed control devices.
l Take care in the vicinity of the shutter / awning / screen
when moving, and keep at a safe distance until the ma-
noeuvre is completed.
l For model E MH / E LH – When performing the man-
ual operation, take great care if the shutter is raised be-
cause it is liable to fall rapidly in the event of weak or bro-
ken springs.
l When cleaning windows in the vicinity of the automation,
do not activate any control devices and if the latter are au-
tomatic, disconnect the power supply.
l Frequently check the automation, to detect for imbal-
ance, any signs of wear or damage to cables or springs (if
present). Do not use the automation if adjustments or re-
pairs are required. In this case always contact a specialised
technician to solve the problem.
2
PRODUCT DESCRIPTION AND
INTENDED USE
This product is a tubular motor designed for the automa-
tion of a shutter, sun awning or solar screen. Any other
use is strictly prohibited! The manufacturer declines
all liability for damage resulting from improper use
of the product and other than as specified in this
manual.
The product has the following features:
l powered via the electrical mains (consult data on the
motor dataplate);
l designed to move the shutter in Ascent and Descent
by means of wall-mounted pushbuttons (not supplied in
pack); the model E MH / E LH is also equipped with a
mechanism for emergency manual manoeuvres, for use in
the event of a power failure;
l is equipped with an electromechanical system that auto-
matically shuts off power supply when the shutter reaches
the set limit positions (fig. 4): position "0" (shutter totally re-
tracted) and position "1" (shutter totally extended);
l install inside the winding roller; the part of the motor that
protrudes from the roller (electronic head) is fixed to the
ceiling or the wall with suitable support brackets (not sup-
plied in pack);
l it is designed for residential use, i.e. discontinuous. It
guarantees a continuous operating time of maximum 4
minutes;
l it is fitted with a thermal cut-out which in the event of
overheating due to use of the automation in excess of the
set limits, automatically shuts off the power supply and on-
ly restores operation when the temperature returns within
the normal range.
l during the installation and adjustment operations, the
motor can be controlled by the "TTU" unit (fig. 6) until the
final electrical connections have been made.