Specifications - SSS Siedle BVPS 850-0 Produktinformation

Performance features
BVPC 850-0:
• 17.8 cm (7") touchscreen, resolu­
tion 800 x 480 pixel
• Integrated video memory, capacity
for over 4000 images with the sup­
plied SD card (8 GB)
• 15 switching/control functions in
conjunction with the bus switching
module BSM/BSE..., selective dialling
of door loudspeakers/cameras
• 15 signal displays
• Optimized depiction of switching/
control functions and messages
• Voice volume adjustable in 3
stages
• Integrated audio and video privacy
device
• Status display with active speech
connection
• Optical call display
• Selective dialling of max. 15 door
loudspeakers/cameras
• Muting and status display
• Parallel switching of max. 8 indoor
stations
• Call differentiation for storey call,
internal call and 2 door calls
• Call generator with 11 call tone
sequences, including chime
• Call volume adjustable in 5 stages
up to max. 83 dB(A)
• Group formation for door calls
• Door release/light function at any
time using bus wires
• Door/video connection possible at
any time
• Base plate pre­installable with
terminals
• Actuation of switching/control
functions in conjunction with the
bus switching module BSM/BSE...
• Feedback for switching/control
functions and messages in conjunc­
tion with bus input module BEM...
• Internal telephony with max.
15 indoor stations
• Call forwarding
• Collective announcement
• Automatic call pick­up with
internal call
• Doormatic on/off/time controlled
• Can be used with table­top acces­
sory ZTVP 850-... as a table-top
device
4
Electrical voltage
Mounting, installation and servicing
work on electrical devices may only
be performed by a suitably qualified
electrician.
Electrostatic charging
As a result of electrostatic charging,
direct contact with the circuit board
can result in destruction of the
device. Direct contact with the circuit
board must therefore be avoided.
Scope of supply
• BVPC/BVPS 850­... (Base plate and
housing with circuit board)
• operating instructions for the end
user
• this product information
Mounting
During installation, where applicable
ensure that the surface is protected
from damage.
1 Recommended mounting height
appr. 1.60 m to display height/
viewing height.
2 Open the device from the back
by releasing the base plate with the
locking lever.
3 Align the base plate centrally
relative to the flush mounted box
and mark the fixing holes. When
mounting directly on the wall,
fasten the base plate using 4 screws,
paying attention that the plate is the
right way up (top marking).
4 Hook the housing into the base
plate from above and close by
exerting a slight pressure.
Dismantling
5 To remove the housing, press
the lock upwards using a flat blade
screwdriver. The circuit board
remains in the housing superstruc-
ture.
Terminal assignment
TaM, TbM In­Home bus monitor
branch
ERT, ETb Storey call button
+M, ­M Supply voltage
10–50 V DC
S1, S1 Potential­free contact
15 V AC, 30 V DC, 1 A
Commissioning
• The basic configuration must be
carried out on every device without
fail.
• Installation and commissioning
procedures are described in the
system manual (enclosed with Bus
Video Line Rectifier BVNG 650-...).
• Functions on the user interface of
the deluxe bus video panel can be
individually named. Programming
takes place using the bus program­
ming software and is transferred to
the BVPC 850-... via the SD card. For
this, an SD card reader is required.

Specifications

Operating voltage: 20–30 V DC
Operating current: max. 400 mA
Contact type: potential-free S1/
S1 max. 15 V AC, 30 V DC, 1 A
switching time 0.4 sec - 19 min
Dimensions (mm) W x H x D:
202 x 202 x 30
Note
As in the as­delivered/de­energized
status, the contact position of the
bistable relay (contact S1/S1) cannot
be defined, the bus supply to the
device must be connected before­
hand to ensure that the bistable
relay functions correctly.
Care instructions
Only ever clean your indoor device
using a soft cloth dampened with
mild soap solution. Dry, aggres­
sive cleaning agents and abrasive
detergents can damage the surface.
Detailed care instructions are located
in the download area of www.siedle.
com.