Product Disposal; Ce Declaration Of Conformity - Nice SHEL60KIT Gebrauchsanleitungen

used and the declaration of conformity compiled by the installer (see section
TECHNICAL DOCUMENTATION) .
2 Affix a dataplate on the door, specifying at least the following data: type of
automation, name and address of manufacturer (responsible for commis-
sioning), serial number, year of construction and CE mark .
3 Prepare and provide the owner with the declaration of conformity; the "CE
Declaration of conformity" in the section TECHNICAL DOCUMENTATION
must be compiled for this purpose .
4 Prepare and provide the owner with the form "Operation manual" in the
section TECHNICAL DOCUMENTATION .
5 Prepare and provide the owner with the form "Maintenance schedule"
in the section TECHNICAL DOCUMENTATION, containing all maintenance
instructions for all devices in the automation .
6 Before commissioning the automation, ensure that the owner is adequately
informed of all associated risks and hazards .
7 Permanently affix a label or plate on the door with the image shown in fig. 46
(minimum height 60 mm) bearing the text "CAUTION: RISK OF CRUSHING".
PERIODIC MAINTENANCE OPERATIONS
In general, this product does not require special maintenance; however, regular
checks over time will ensure system efficiency and correct operation of the
safety systems installed .
Therefore to ensure correct maintenance, refer to the chapter "Maintenance
Schedule" in the section "TECHNICAL DOCUMENTATION" at the end of the
manual .
Declaration in accordance with Directives: 1999/5/EC (R&TTE), 2004/108/EC (EMC); 2006/42/EC (MD) annex II, part B
Note - The content of this declaration corresponds to the declaration made in the official document filed in the offices of Nice S.p.a., and particularly the latest version thereof
available prior to the printing of this manual. The text contained here has been adapted to meet editorial requirements. A copy of the original declaration may be requested from
Nice S.p.a. (TV) I.
Declaration number: 562/SHEL
Name of manufacturer:
Address:
Person authorized to provide
technical documentation:
Product type:
Model / Type:
Accessories:
The undersigned Roberto Griffa, as Chief Executive Officer, hereby declares under his own responsibility that the products identified above comply with the
provisions of the following directives:
• Directive 1999/5/CE OF THE EUROPEAN PARLIAMENT AND COUNCIL dated March 9 1999 regarding radios and communications terminals and recip-
rocal recognition of their conformity in accordance with the following harmonized standards:
- Protection of health (art. 3(1)(a)): EN 62479:2010
- Electrical safety (art. 3(1)(a)): EN 60950-1:2006 + A11:2009+A12:2011+A1:2010+A2:2013
- Electromagnetic compatibility (art. 3(1)(b)): EN 301 489-1 V1.9.2:2011, EN 301 489-3 V1.6.1:2013
- Radio spectrum (art. 3(2)): EN 300 220-2 V2.4.1:2012
• DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of December 15 2004 concerning alignment of Member States' legislation
regarding electromagnetic compatibility and abrogating directive 89/336/EEC, according to the following harmonized standards:
EN 61000-6-2:2005, EN 61000-6-3:2007+A1:2011
The product also complies with the following directive in accordance with the requirements for "quasi-machines":
• Directive 2006/42/EC OF THE EUROPEAN PARLIAMENT AND COUNCIL of May 17 2006 regarding machines and amending directive 95/16/EC (con-
solidated text)
- I declare that the pertinent technical documentation has been prepared in accordance with Annex VII B to Directive 2006/42/EC and that the following essential requirements
have been met: 1 .1- 1 .1 .2- 1 .1 .3- 1 .2 .1-1 .2 .6- 1 .5 .1-1 .5 .2- 1 .5 .5- 1 .5 .6- 1 .5 .7- 1 .5 .8- 1 .5 .10- 1 .5 .11
- The manufacturer agrees to send the national authorities pertinent information on the "quasi-machine" in response to a motivated request without affecting its intellectual
property rights .
- If the "quasi-machine" is operated in a European country with an official language other than the language used in this declaration, the importer must associate a translation
with this declaration .
- The "quasi-machine" must not be operated until the final machine in which it is to be incorporated is declared to conform to the provisions of Directive 2006/42/EC, if applicable
to it .
The product also complies with the following standards: EN 60335-1:2002 + A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 +
A15:2011, EN 60335-2-103:2003+A11:2009
The parts of the product which are subject to the following standards comply with them: EN 13241-1:2003+A1:2011, EN 12445:2002, EN 12453:2002,
EN 12978:2003+A1:2009
Oderzo, 16 March 2016

CE DECLARATION OF CONFORMITY

Revision: 0 Language: EN
NICE S .p .A .
Via Pezza Alta 13, Rustignè Industrial Zone, 31046 Oderzo (TV) Italy
NICE S .p .A .
Electro-mechanical gearmotor and relative accessories
SHEL60, SHEL75
Radio controls of the series FLO, FLOR, Smilo

PRODUCT DISPOSAL

This product is an integral part of the automation and therefore must
be disposed together with the latter.
As in installation, also at the end of product lifetime, the disassembly and
scrapping operations must be performed by qualified personnel.
This product comprises various types of materials: some may be recycled oth-
ers must be disposed of . Seek information on the recycling and disposal sys-
tems envisaged by the local regulations in your area for this product category .
Caution! – some parts of the product may contain pollutant or hazardous sub-
stances which, if disposed of into the environment, may cause serious damage
to the environment or physical health .
As indicated by the symbol alongside, disposal of this prod-
uct in domestic waste is strictly prohibited . Separate the
waste into categories for disposal, according to the meth-
ods envisaged by current legislation in your area, or return
the product to the retailer when purchasing a new version .
Caution! – Local legislation may envisage serious fines in
the event of abusive disposal of this product .
Ing . Roberto Griffa (Chief Executive Officer)
English – 9