About This Document - Wieland SP-SDI Gebrauchsanleitung

TRANSLATION OF THE ORIGINAL INSTRUCTIONS
SP-SDI / SP-SDIO
Expansion modules of the configurable safety
®
controller samos PRO
BA000515 - 11/2013 (Rev. F)
Wieland Electric GmbH
Brennerstr. 10-14
D-96052 Bamberg
www.wieland-electric.com
Printed in Germany • All Rights reserved
1

About this document

1.1 Documentation for the system samos
This installation manual describes the installation of the controller
module of the configurable safety control samos®PRO.
The installation of the samos®PRO expansion modules SP-SDIO
and SP-SDI, the relay-modules SA-OR-S2-2RK and SA-OR-S1-4RK is
described in separate installation manuals.
Installation, configuration and operation of the configurable
safety control samos®PRO is described in the system manuals
„samos®PRO Hardware" and „samos®PLAN Software".
Document Title
Manual samos®PRO Hardware
Manual samos®PLAN Software
Above all, technical knowledge in the installation of protection on
machinery is necessary, which is not part of this manual.
1.2 Function of this document
This installation manual is intended for the technical staff of the
machine builder or machine operator enabling safe installation of the
controller module of the configurable safety control samosPRO.
This installation manual is not a manual for the operation of the
machine. Information about that is part of the manual of the
machine.
2 On safety
This chapter is for your safety and the safety of the machine opera-
tor.
> Please read this chapter carefully before starting the installation.
2.1 Qualified persons
The configurable safety controller samosPRO has to be installed by
qualified persons.
Qualified is, who...
has an adequate technical education and
is instructed by the machine builder in the operation of the
machine and the significant safety guidelines and
has access to the manuals of samosPRO and has read and
understood these manuals and
has access to the manuals of the protection equipment of the
machine being connected to the configurable safety controller
samos®PRO and has read and understood these manuals.
2.2 Application area of the system
samosPRO is a configurable safety controller for safety applications
and is applicable
according to EN 61508 up to SIL 3
according to EN 62061 up to SIL CL 3
according to EN ISO 13849-1:2006 up to Performance Level (PL) e
according to EN ISO 13849-1 up to category 4
The actual level of safety depends on the wiring, the parameteriza-
tion, the switching elements and its installation on the machinery.
The configurable safety control samos®PRO is monitoring tactile
switching safety elements (e.g. E-Stop buttons, safety switches,
safety interlocks, lightcurtains, laser scanner) and processing their
signals.
With its safe switching outputs the configurable safety control
samos®PRO can switch off actuators (e.g. contactors, magnets,
valves) of machines or plants.
2.3 Intended operation
The configurable safety control samos®PRO is operating only within
its specified operating limits (voltage, temperature etc., see technical
data and chapter „Application area of the system"). The system has
to be operated only by experts and on the machine on which the
EN
system is mounted according to the operation manuals (BA000497
und BA000518) by qualified staff.
With any different usage or changes of the modules – even for
installation – all warranty claims to Wieland Electric GmbH are lost.
2.4 General safety advices and safety measures
WARNING WARNING
WARNING WARNING
®
PRO
With installation and operation of the configurable safety control-
ler samos®PRO you have to respect the local standards and di-
rective in your country.
For installation and use of the configurable safety controller
samos®PRO and for service and maintenance of the system na-
tional laws and directives are binding, specially
– the EMC-Directive 2004/108/EC
– the Machine Directive 2006/42/EC.
– the Safety Requirements of the Work Directive 89/655/EC.
Number
– the Low-voltage-directive 2006/95/EC
BA000497
– the Lift directive 1995/16/EC
BA000518
– the Health and safety at Work Act / Safety guidelines.
Manufacturer and operator of the machine, using a configurable
safety controller samos®PRO, have to respect all legally binding
safety regulations at their own responsibility in coordination with
the responsible authorities.
All advices and tests described in the manuals must be respected
necessarily.
All tests during the installation have to be made by trained staff
respectively by specially instructed personal and the tests have to
be documented in a comprehensible way.
The external voltage supply of the modules has to bridge gaps of
voltage of 20 ms according to EN 60204. Appropriate power sup-
plies are available from Wieland Electric as accessory.
The modules of the system samos®PRO comply with class A,
group 1 according to EN 55011.
– The group 1 covers all ISM-devices, where HF-energy is pro-
duced and/or used for the inner function of the device.
WARNING WARNING
WARNING WARNING
2.5 Disposal
The disposal of defective modules has to be done in accordance
with the local regulations for waste disposal (e.g. European code for
waste 16 02 14).
Pay attention to the safety advices and protec-
tion measures!
Notice the following hints in order to guarantee the
intended operation of the configurable safety
controller samos®PRO.
The system samos®PRO samos®PRO covers the requirements samos®PRO samos®PRO
for class A (Industrial Use) according to EN
55011!
Therefore samos®PRO -System is designed only for
the use in the industrial environment and it is not
designed for the use in the private environment.
5 5 5 5