Specifications; Rotary Hammer Safety Warnings - Makita HR2010 Betriebsanleitung

ENGLISH
(Original instructions)
1 Switch trigger
2 Side grip
3 Bit shank
4 Bit grease
5 Bit
6 Chuck cover
7 Depth gauge

SPECIFICATIONS

Model
Capacities
Concrete............................................................. 20 mm
Steel ................................................................... 13 mm
Wood .................................................................. 24 mm
–1
No load speed (min ).......................................... 0 – 900
Blows per minute............................................... 0 – 4,000
Overall length ...................................................... 302 mm
Net weight ............................................................. 3.4 kg
Safety class .............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for hammer drilling in brick, concrete
and stone.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.

ROTARY HAMMER SAFETY WARNINGS

1. Wear ear protectors. Exposure to noise can cause
hearing loss.
2. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
3. Hold power tools by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
4
Explanation of general view
8 Clamp screw
9 Grip base
10 Drill chuck
11 Chuck adapter
12 Commutator
13 Insulating tip
14 Carbon brush
4.
HR2010
5.
6.
/II
7.
8.
ENE041-1
9.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
ENF002-2
12. Do not point the tool at any one in the area when
13. Do not touch the bit or parts close to the bit
14. Some material contains chemicals which may be
GEA010-1
SAVE THESE INSTRUCTIONS.
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
GEB007-7
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
15 Screwdriver
16 Brush holder cap
17 Lock nut wrench
18 Crank cap
19 Hammer grease
Wear a hard hat (safety helmet), safety glasses
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly
recommended that you wear a dust mask and
thickly padded gloves.
Be sure the bit is secured in place before opera-
tion.
Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
In cold weather or when the tool has not been
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
Hold the tool firmly with both hands.
only when hand-held.
operating. The bit could fly out and injure some-
one seriously.
immediately after operation; they may be
extremely hot and could burn your skin.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
WARNING: